Build an M3 Anvil! Cluster
Revision as of 22:53, 28 July 2023 by Digimer (talk | contribs) (→Striker Dashboards; Installing anvil-striker)
|
Alteeve Wiki :: How To :: Build an M3 Anvil! Cluster |
First off, what is an Anvil!?
In short, it's a system designed to keep servers running through an array of failures, without need for an internet connection.
Think about ship-board computer systems, remote research facilities, factories without dedicated IT staff, un-staffed branch offices and so forth. Where most hosted solutions expect for technical staff to be available in short order, and Anvil! is designed to continue functioning properly for weeks or months with faulty components.
In these cases, the Anvil! system will predict component failure and mitigate automatically. It will adapt to changing threat conditions, like cooling or power loss, including automatic recovery from full power loss. It is designed around the understanding that a fault condition may not be repaired for weeks or months, and can do automated risk analysis and mitigation.
That's an Anvil! cluster!
An Anvil! cluster is designed so that any component in the cluster can fail, be removed and a replacement installed without needing a maintenance window. This includes power, network, compute and management systems.
Components
The minimum configuration needed to host servers on an Anvil! is this;
| Management Layer | |
|---|---|
| Striker Dashboard 1 | Striker Dashboard 2 |
| Anvil! Node | |
| Node 1 | |
| Subnode 1 | Subnode 2 |
| Foundation Pack 1 | |
| Ethernet Switch 1 | Ethernet Switch 2 |
| Switched PDU 1 | Switched PDU 2 |
| UPS 1 | UPS 2 |
With this configuration, you can host as many servers as you would like, limited only by the resources of Node 1 (itself made of a pair of physical nodes with your choice of processing, RAM and storage resources).
Scaling
To add capacity for hosted servers, individual nodes can be upgraded (online!), and/or additional nodes can be added. There is no hard limit on how many nodes can be in a given cluster.
Each 'Foundation Pack' can handle as many nodes as you'd like, though for reasons we'll explain in more detail later, it is recommended to run two to four nodes per foundation pack.
Management Layer; Striker Dashboards
The management layer, the Striker dashboards, have no hard limit on how many Node Blocks they can manage. All node-blocks record their data to the Strikers (to offload processing and storage loads). There is a practical limit to how many node blocks can use the Strikers, but this can be accounted for in the hardware selected for the dashboards.
Nodes
An Anvil! cluster uses one or more nodes, with each node being a pair of matched physical subnodes configured as a single logical unit. The power of a given node block is set by you and based on the loads you expect to place on it.
There is no hard limit on how many node blocks exist in an Anvil! cluster. Your servers will be deployed across the node blocks and, when you want to add more servers than you currently have resource for, you simple add another node block.
Foundation Packs
A foundation pack is the power and ethernet layer that feeds into one or more node blocks. At it's most basic, it consists of three pairs of equipment;
- Two stacked (or VLT-domain'ed) ethernet switches.
- Two switched PDUs (network-switched power bars
- Two UPSes.
Each UPS feeds one PDU, forming two separate "power rails". Ethernet switches and all sub-nodes are equipped with redundant PSUs, with one PSU fed by either power rail.
In this way, any component in the foundation pack can fault, and all equipment will continue to have power and ethernet resources available. How many Anvil! node-pairs can be run on a given foundation pack is limited only by the sizing of the selected foundation pack equipment.
Configuration
 |
Note: This is SUPER basic and minimal at this stage. |
Striker Dashboards
Striker dashboards are often described as "cheap and cheerful", generally being a fairly small and inexpensive device, like a Dell Optiplex 3090, Intel NUC, or similar.
You can choose any vendor you wish, but when selecting hardware, be mindful that all Scancore data is stored in PostgreSQL databases running on each dashboard. As such, we recommend an Intel Core i5 or AMD Ryzen 5 class CPU, 8 GiB or more of RAM, a ~250 GiB SSD (mixed use, decent IOPS) storage and two ethernet ports.
Striker Dashboards host the Striker web interface, and act as a bridge between your IFN network and the Anvil! cluster's BCN management network. As such, they must have a minimum of two ethernet ports.
Node Pairs
An Anvil! Node Pair is made up of two identical physical machines. These two machines act as a single logical unit, providing fault tolerance and automated live migrations of hosted servers to mitigate against predicted hardware faults.
Each sub-node (a single hardware node) must have;
- Redundant PSUs
- Six ethernet ports (eight recommended). If six, use 3x dual-port. If eight, 2x quad port will do.
- Redundant storage (RAID level 1 (mirroring) or level 5 or 6 (striping with parity). Sufficient capacity and IOPS to host the servers that will run on each pair.
- IPMI (out-of-band) management ports. Strongly recommend on a dedicated network interface.
- Sufficient CPU core count and core speed for expected hosted servers.
- Sufficient RAM for the expected servers (note that the Anvil! reserves 8 GiB).
Disaster Recovery (DR) Host
Optionally, a "third node" of a sort can be added to a node-pair. This is called a DR Host, and should (but doesn't have to be) identical to the node pair hardware it is extending.
A DR (disaster recovery) Host acts as a remotely hosted "third node" that can be manually pressed into service in a situation where both nodes in a node pair are destroyed. A common example would be a DR Host being in another building on a campus installation, or on the far side of the building / vessel.
A DR host can in theory be in another city, but storage replication speeds and latency need to be considered. Storage replication between node pairs is synchronous, where replication to DR can be asynchronous. However, consideration of storage loads are required to insure that storage data can keep up with the rate of data change.
Foundation Pack Equipment
The Anvil! is, fundamentally, hardware agnostic. That said, the hardware you select must be configured to meet the Anvil! requirements.
As we are hardware agnostic, we've created three linked pages. As we validate hardware ourselves, we will expand hardware-specific configuration guides. If you've configured foundation pack equipment not in the pages below, and you are willing, we would love to add your configuration instructions to our list.
Striker, Node and DR Host Configuration
In UEFI (BIOS), configure;
- Striker Dashboards to power on after power loss in all cases.
- Configure Subnodes to stay powered off after power loss in all cases.
- Configure any machines with redundant PSUs to balance the load across PSUs (don't use "hot spare" where only one PSU is active carrying the full load)
If using RAID
- If you have two drives, configure RAID level 1 (mirroring)
- If using 3 to 8 drives, configure RAID level 5 (striping with N-1 parity)
- If using 9+ drives, configure RAID level 6 (striping with N-2 parity)
Note that a server on a given node-pair will have it's data mirrored, effectively creating a sort of RAID level 11 (mirror of mirrors), 15 (mirror of N-1 stripes) or 16 (mirror of N-2 stripes). This is why we're comfortable pushing RAID level 5 to 8 disks.
Installation of Base OS
For all three machine types; (striker dashboards, node-pair sub-node, dr host), begin with a minimal RHEL 8 or CentOS Stream 8 install.
|
Note: This tutorial assumes an existing understanding of installed RHEL 8. If you are new to RHEL, you can setup a free Red Hat account, and then follow their installation guide. |
Base OS Install
|
Note: Every effort has been made in the development of the Anvil! to ensure it will work with localisations. However, parsing of command output has been tested with Canadian and American English. As such, it is recommended that you install using one of these localisations. If you use a different localisation, and run into any problems, please let us know and we will try to add support. |
Localisation
Choose your localisation;
KDUMP
Disable kdump; This prevents kernel dumps if the OS crashes, but it means the host will recover faster. If you want to leave kdump enabled, that is fine, but be aware of the slower recovery times. Note that a subnode getting fenced will be forced off, and so kernel dumps won't be collected regardless of this configuration.
Network & Host Name
Set the host name for the machine. It's useful to do this before configuring the network, so that the volume group name includes the host's short host name. This doesn't effect the operation of the Anvil! system, but it can assist with debugging down the road.
|
Note: Don't worry about configuring the network, this will be handles by the Anvil! later. Setting the IFN IP at this stage can be useful, but is not required. |
Time & Date
Setting the timezone is very much specific to you and your install. The most important part is that the time zone is set consistently across all machines in the Anvil! cluster.
Software Selection
All machines can start with a Minimal Install. On Strikers, if you'd prefer to use Server With GUI, that is fine, but it is not needed at this step. The anvil-striker RPM will pull in the graphical interface.
|
Note: If you select a graphical install on a Striker Dashboard, create a user called admin and set a password for that user. |
Installation Destination
|
Note: It is strongly suggested to set the host name before configuring storage. |
|
Note: This is where the installation of a Striker dashboard will differ from an Anvil! Node's sub-node or DR host |
In this example, there is a single hard drive that will be configured. It's entirely valid to have a dedicated OS drive, and using a second drive for hosting servers. If you're planning to use a different storage plan, then you can ignore this stage. The key requirement is that there is unused space sufficiently large to host the servers you plan to run on a given node or DR host.
| Striker Dashboards | Anvil! Subnodes and DR Hosts |
|---|---|
Click on Click here to create them automatically. This will create the base storage configuration, which we will adapt.
| Striker Dashboards | Anvil! Subnodes and DR Hosts |
|---|---|
In all cases, the auto-created /home logical volume will be deleted.
- For Striker dashboards, after deleting /home, assign the freed space to the / partition. To do this, select the / partition, and set the Desired Capacity to some much larger size than is available (like 1TiB), and click on Update Setting. The size will change to the largest valid value.
- For Anvil! subnodes and DR hosts, simply delete the /home partition, and do not give the free space to /. The space freed up by deleting /home will be used later for hosting servers.
| Striker Dashboards | Anvil! Subnodes and DR Hosts |
|---|---|
From this point forward, the rest of the OS install is the same for all systems.
Optional; Connect to Red Hat
If you are installing RHEL 8, as opposed to CentOS Stream 8, you can register the server during installation. If you don't do this, the Anvil! will give you a chance to register the server during the installation process also.
Root Password
Set the root user password.
Begin Installation
With everything selected, click on Begin Installation. When the install has completed, reboot into the minimal install.
Post OS Install Configuration
Setting up the Alteeve repos is the same, but after that, the steps start to diverge depending on which machine type we're setting up in the Anvil! cluster.
Installing the Alteeve Repo
|
Note: Our repo pulls in a bunch of other packages that will be needed shortly. |
There are two Alteeve repositories that you can install; Community and Enterprise. Which is used is selected after the repository RPM is installed. Lets install the repo RPM, and then we will discuss the differences before we select one.
dnf install https://www.alteeve.com/an-repo/m3/anvil-release-latest.noarch.rpm
Updating Subscription Management repositories.
Last metadata expiration check: 0:39:42 ago on Fri 28 Jul 2023 04:21:39 PM EDT.
anvil-release-latest.noarch.rpm 59 kB/s | 12 kB 00:00
Dependencies resolved.
==================================================================================================================================
Package Arch Version Repository Size
==================================================================================================================================
Installing:
alteeve-release noarch 0.1-2 @commandline 12 k
Installing dependencies:
dwz x86_64 0.12-10.el8 rhel-8-for-x86_64-appstream-rpms 109 k
efi-srpm-macros noarch 3-3.el8 rhel-8-for-x86_64-appstream-rpms 22 k
ghc-srpm-macros noarch 1.4.2-7.el8 rhel-8-for-x86_64-appstream-rpms 9.4 k
go-srpm-macros noarch 2-17.el8 rhel-8-for-x86_64-appstream-rpms 13 k
make x86_64 1:4.2.1-11.el8 rhel-8-for-x86_64-baseos-rpms 498 k
ocaml-srpm-macros noarch 5-4.el8 rhel-8-for-x86_64-appstream-rpms 9.5 k
openblas-srpm-macros noarch 2-2.el8 rhel-8-for-x86_64-appstream-rpms 8.0 k
perl x86_64 4:5.26.3-422.el8 rhel-8-for-x86_64-appstream-rpms 73 k
<...snip...>
perl-version x86_64 6:0.99.24-1.el8 rhel-8-for-x86_64-appstream-rpms 67 k
python-rpm-macros noarch 3-45.el8 rhel-8-for-x86_64-appstream-rpms 16 k
python-srpm-macros noarch 3-45.el8 rhel-8-for-x86_64-appstream-rpms 16 k
python3-pyparsing noarch 2.1.10-7.el8 rhel-8-for-x86_64-baseos-rpms 142 k
python3-rpm-macros noarch 3-45.el8 rhel-8-for-x86_64-appstream-rpms 15 k
qt5-srpm-macros noarch 5.15.3-1.el8 rhel-8-for-x86_64-appstream-rpms 11 k
redhat-rpm-config noarch 131-1.el8 rhel-8-for-x86_64-appstream-rpms 91 k
rust-srpm-macros noarch 5-2.el8 rhel-8-for-x86_64-appstream-rpms 9.3 k
systemtap-sdt-devel x86_64 4.8-2.el8 rhel-8-for-x86_64-appstream-rpms 88 k
unzip x86_64 6.0-46.el8 rhel-8-for-x86_64-baseos-rpms 196 k
zip x86_64 3.0-23.el8 rhel-8-for-x86_64-baseos-rpms 270 k
Installing weak dependencies:
perl-Encode-Locale noarch 1.05-10.module+el8.3.0+6498+9eecfe51 rhel-8-for-x86_64-appstream-rpms 22 k
perl-IO-Socket-SSL noarch 2.066-4.module+el8.3.0+6446+594cad75 rhel-8-for-x86_64-appstream-rpms 298 k
perl-Mozilla-CA noarch 20160104-7.module+el8.3.0+6498+9eecfe51 rhel-8-for-x86_64-appstream-rpms 15 k
perl-TermReadKey x86_64 2.37-7.el8 rhel-8-for-x86_64-appstream-rpms 40 k
Enabling module streams:
perl 5.26
perl-IO-Socket-SSL 2.066
perl-libwww-perl 6.34
Transaction Summary
==================================================================================================================================
Install 159 Packages
Total size: 23 M
Total download size: 23 M
Installed size: 64 M
Is this ok [y/N]:
Downloading Packages:
(1/158): perl-Scalar-List-Utils-1.49-2.el8.x86_64.rpm 173 kB/s | 68 kB 00:00
(2/158): perl-Data-Dumper-2.167-399.el8.x86_64.rpm 147 kB/s | 58 kB 00:00
(3/158): perl-PathTools-3.74-1.el8.x86_64.rpm 155 kB/s | 90 kB 00:00
(4/158): perl-threads-shared-1.58-2.el8.x86_64.rpm 127 kB/s | 48 kB 00:00
(5/158): perl-Unicode-Normalize-1.25-396.el8.x86_64.rpm 431 kB/s | 82 kB 00:00
(6/158): zip-3.0-23.el8.x86_64.rpm 896 kB/s | 270 kB 00:00
(7/158): perl-MIME-Base64-3.15-396.el8.x86_64.rpm 101 kB/s | 31 kB 00:00
(8/158): perl-Pod-Simple-3.35-395.el8.noarch.rpm 879 kB/s | 213 kB 00:00
<...snip...>
(156/158): python-srpm-macros-3-45.el8.noarch.rpm 65 kB/s | 16 kB 00:00
(157/158): perl-open-1.11-422.el8.noarch.rpm 818 kB/s | 78 kB 00:00
(158/158): perl-utils-5.26.3-422.el8.noarch.rpm 269 kB/s | 129 kB 00:00
----------------------------------------------------------------------------------------------------------------------------------
Total 1.6 MB/s | 23 MB 00:14
Running transaction check
Transaction check succeeded.
Running transaction test
Transaction test succeeded.
Running transaction
Preparing : 1/1
Installing : perl-Digest-1.17-395.el8.noarch 1/159
Installing : perl-Digest-MD5-2.55-396.el8.x86_64 2/159
Installing : perl-Data-Dumper-2.167-399.el8.x86_64 3/159
Installing : perl-libnet-3.11-3.el8.noarch 4/159
Installing : perl-Net-SSLeay-1.88-2.module+el8.6.0+13392+f0897f98.x86_64 5/159
<...snip...>
Installing : perl-CPAN-2.18-397.el8.noarch 156/159
Installing : perl-Encode-devel-4:2.97-3.el8.x86_64 157/159
Installing : perl-4:5.26.3-422.el8.x86_64 158/159
Installing : alteeve-release-0.1-2.noarch 159/159
Running scriptlet: alteeve-release-0.1-2.noarch 159/159
Verifying : perl-Scalar-List-Utils-3:1.49-2.el8.x86_64 1/159
Verifying : perl-PathTools-3.74-1.el8.x86_64 2/159
Verifying : perl-Data-Dumper-2.167-399.el8.x86_64 3/159
Verifying : perl-threads-shared-1.58-2.el8.x86_64 4/159
Verifying : perl-Encode-4:2.97-3.el8.x86_64 5/159
<...snip...>
Verifying : python-srpm-macros-3-45.el8.noarch 155/159
Verifying : perl-SelfLoader-1.23-422.el8.noarch 156/159
Verifying : perl-open-1.11-422.el8.noarch 157/159
Verifying : perl-utils-5.26.3-422.el8.noarch 158/159
Verifying : alteeve-release-0.1-2.noarch 159/159
Installed products updated.
Installed:
alteeve-release-0.1-2.noarch dwz-0.12-10.el8.x86_64
efi-srpm-macros-3-3.el8.noarch ghc-srpm-macros-1.4.2-7.el8.noarch
<...snip...>
redhat-rpm-config-131-1.el8.noarch rust-srpm-macros-5-2.el8.noarch
systemtap-sdt-devel-4.8-2.el8.x86_64 unzip-6.0-46.el8.x86_64
zip-3.0-23.el8.x86_64
Complete!
Selecting a Repository
There are two released version of the Anvil! cluster. There are pros and cons to both options;
Community Repo
The Community repository is the free repo that anyone can use. As new builds pass our CI/CD test infrastructure, the versions in this repository are automatically built.
This repository always has the latest and greatest from Alteeve. We use Jenkins and a suite of proprietary test suite to ensure that the quality of the releases is excellent. Of course, Alteeve is a company of humans, and there's always a small chance that a bug could get through. Our free community repository is community supported, and it's our wonderful users who help us improve and refine our Anvil! platform.
Enterprise Repo
The Enterprise repository is the paid-access repository. The releases in the enterprise repo are "cherry picked" by Alteeve, and subjected to more extensive testing and QA. This repo is designed for businesses who want the most stable releases.
Using this repo opens up the option of active monitoring of your Anvil! cluster by Alteeve, also!
If you choose to get the Enterprise repo, please contact us and we will provide you with a custome repository key.
Configuring the Alteeve Repo
To configure the repo, we will use the alteeve-repo-setup program that was just installed.
You can see a full list of options, including the use of the --key <uuid> to enable to Enterprise Repo. For this tutorial, we will configure the community repo.
alteeve-repo-setup
You have not specified an Enterprise repo key. This will enable the community
repository. We work quite hard to make it as stable as we possibly can, but it
does lead Enterprise.
Proceed? [y/N]:
Writing: [/etc/yum.repos.d/alteeve-anvil.repo]...
Repo: [rhel-8] created successfuly.
This is RHEL 8. Once subscribed, please enable this repo;
# subscription-manager repos --enable codeready-builder-for-rhel-8-x86_64-rpms
NOTE: On *nodes*, also add the High-Availability Addon repo as well;
# subscription-manager repos --enable rhel-8-for-x86_64-highavailability-rpms
If you are installing using CentOS Stream 8, you are done now and can move on.
RHEL 8 Additional Repos
If you are using RHEL 8 proper, with the system now subscribed, we now need to enable additional repositories
On all systems;
subscription-manager repos --enable codeready-builder-for-rhel-8-x86_64-rpms
Repository 'codeready-builder-for-rhel-8-x86_64-rpms' is enabled for this system.
On Anvil! subnodes only, not Striker dashboards or DR hosts.
subscription-manager repos --enable rhel-8-for-x86_64-highavailability-rpms
Repository 'rhel-8-for-x86_64-highavailability-rpms' is enabled for this system.
Is this ok [y/N]:
Running transaction check
Transaction check succeeded.
Running transaction test
Transaction test succeeded.
Running transaction
Preparing : 1/1
Erasing : biosdevname-0.7.3-2.el8.x86_64 1/1
Running scriptlet: biosdevname-0.7.3-2.el8.x86_64 1/1
Verifying : biosdevname-0.7.3-2.el8.x86_64 1/1
Installed products updated.
Removed:
biosdevname-0.7.3-2.el8.x86_64
Complete!
Installing Anvil! Packages
This is the step where, from a software perspective, Anvil! cluster systems differentiate to become Striker Dashboards, Anvil! subnodes, and DR hosts. Which a given machine becomes depends on which RPM is installed. The three RPMs that set a machine's role are;
| Striker Dashboards: | anvil-striker |
|---|---|
| Anvil! Subnodes: | anvil-node |
| DR Hosts: | anvil-dr |
Removing biosdevname
|
Note: When M3 is ported to EL9, the network interfaces will no longer be renamed in the same manner, and removing biosdevname will no longer be required. |
Before we can install these RPMs, though, we need to remove the package called biosdevname. Anvil! M3 on EL8 renames the network interfaces to reflect their role. By default, network interfaces are named using predictive names based on their physical location in the machine. Removing this package disables that feature and allows us to rename the interfaces
dnf remove biosdevname
Is this ok [y/N]:
Updating Subscription Management repositories.
Dependencies resolved.
-=================================================================================================================================
Package Architecture Version Repository Size
-=================================================================================================================================
Removing:
biosdevname x86_64 0.7.3-2.el8 @rhel-8-for-x86_64-baseos-rpms 67 k
Transaction Summary
-=================================================================================================================================
Remove 1 Package
Freed space: 67 k
Striker Dashboards; Installing anvil-striker
Now we're ready to install!
|
Note: Given the install of the OS was minimal, these RPMs pull in a lot of RPMs. The output below is truncated. |
Thus, let's install the RPMs on our systems.
dnf install anvil-striker
Updating Subscription Management repositories.
Last metadata expiration check: 0:07:31 ago on Fri 28 Jul 2023 06:00:20 PM EDT.
Dependencies resolved.
-=================================================================================================================================
Package Arch Version Repository Size
-=================================================================================================================================
Installing:
anvil-striker noarch 2.90-1.2704.25b460.el8 anvil-community-rhel-8 3.7 M
Installing dependencies:
GConf2 x86_64 3.2.6-22.el8 rhel-8-for-x86_64-appstream-rpms 1.0 M
ModemManager-glib x86_64 1.20.2-1.el8 rhel-8-for-x86_64-baseos-rpms 338 k
NetworkManager-initscripts-updown
noarch 1:1.40.16-3.el8_8 rhel-8-for-x86_64-baseos-rpms 143 k
SDL x86_64 1.2.15-39.el8 rhel-8-for-x86_64-appstream-rpms 218 k
<...snip...>
telnet x86_64 1:0.17-76.el8 rhel-8-for-x86_64-appstream-rpms 72 k
vino x86_64 3.22.0-11.el8 rhel-8-for-x86_64-appstream-rpms 461 k
xorg-x11-server-Xorg x86_64 1.20.11-15.el8 rhel-8-for-x86_64-appstream-rpms 1.5 M
Enabling module streams:
llvm-toolset rhel8
nodejs 10
perl-App-cpanminus 1.7044
perl-DBD-Pg 3.7
perl-DBI 1.641
perl-YAML 1.24
postgresql 10
python36 3.6
Transaction Summary
-=================================================================================================================================
Install 686 Packages
Total download size: 601 M
Installed size: 2.1 G
Is this ok [y/N]:
Downloading Packages:
(1/686): htop-3.2.1-1.el8.x86_64.rpm 549 kB/s | 172 kB 00:00
(2/686): perl-Algorithm-C3-0.11-6.el8.noarch.rpm 457 kB/s | 29 kB 00:00
(3/686): perl-Class-C3-0.35-6.el8.noarch.rpm 781 kB/s | 37 kB 00:00
(4/686): perl-Data-Dumper-Concise-2.023-16.el8.noarch.rpm 503 kB/s | 26 kB 00:00
(5/686): anvil-core-2.90-1.2704.25b460.el8.noarch.rpm 2.0 MB/s | 1.0 MB 00:00
(6/686): perl-Data-Validate-Domain-0.15-2.el8.noarch.rpm 598 kB/s | 28 kB 00:00
(7/686): perl-Data-Validate-IP-0.30-4.el8.noarch.rpm 581 kB/s | 33 kB 00:00
(8/686): perl-Devel-ArgNames-0.03-23.el8.noarch.rpm 233 kB/s | 13 kB 00:00
(9/686): perl-Email-Date-Format-1.005-21.el8.noarch.rpm 368 kB/s | 22 kB 00:00
(10/686): perl-Email-Find-0.10-39.el8.noarch.rpm 505 kB/s | 23 kB 00:00
(11/686): anvil-striker-2.90-1.2704.25b460.el8.noarch.rpm 5.7 MB/s | 3.7 MB 00:00
(12/686): perl-Email-Valid-1.202-17.el8.noarch.rpm 675 kB/s | 28 kB 00:00
(13/686): perl-Eval-WithLexicals-1.003006-15.el8.noarch.rpm 508 kB/s | 21 kB 00:00
(14/686): perl-Exporter-Declare-0.114-19.el8.noarch.rpm 1.1 MB/s | 51 kB 00:00
(15/686): perl-Future-0.48-1.el8.noarch.rpm 2.1 MB/s | 106 kB 00:00
(16/686): perl-HTML-FromText-2.07-23.el8.noarch.rpm 591 kB/s | 26 kB 00:00
(17/686): perl-HTML-Strip-2.10-21.el8.x86_64.rpm 713 kB/s | 31 kB 00:00
(18/686): perl-Log-Contextual-0.008001-14.el8.noarch.rpm 1.2 MB/s | 67 kB 00:00
(19/686): perl-Log-Dispatch-2.70-6.el8.noarch.rpm 1.7 MB/s | 91 kB 00:00
(20/686): perl-Log-Dispatch-FileRotate-1.38-3.el8.noarch.rpm 896 kB/s | 38 kB 00:00
(21/686): perl-Log-Journald-0.30-2.el8.x86_64.rpm 715 kB/s | 27 kB 00:00
(22/686): perl-MIME-Lite-3.033-3.el8.noarch.rpm 2.2 MB/s | 103 kB 00:00
(23/686): perl-Mail-RFC822-Address-0.3-37.el8.noarch.rpm 392 kB/s | 18 kB 00:00
(24/686): perl-Log-Log4perl-1.54-4.el8.noarch.rpm 4.1 MB/s | 376 kB 00:00
(25/686): perl-Mail-Sendmail-0.80-14.el8.noarch.rpm 922 kB/s | 41 kB 00:00
(26/686): perl-Meta-Builder-0.004-11.el8.noarch.rpm 598 kB/s | 27 kB 00:00
(27/686): perl-Moo-2.005004-4.el8.noarch.rpm 1.6 MB/s | 74 kB 00:00
(28/686): perl-Net-Domain-TLD-1.75-17.el8.noarch.rpm 829 kB/s | 41 kB 00:00
(29/686): perl-Net-Netmask-2.0001-4.el8.noarch.rpm 1.0 MB/s | 47 kB 00:00
(30/686): perl-Net-OpenSSH-0.82-1.el8.noarch.rpm 2.4 MB/s | 120 kB 00:00
(31/686): perl-Net-SSH2-0.72-5.el8.x86_64.rpm 2.5 MB/s | 129 kB 00:00
(32/686): perl-Object-Remote-0.004001-8.el8.noarch.rpm 1.6 MB/s | 73 kB 00:00
(33/686): perl-Proc-Simple-1.32-18.el8.noarch.rpm 573 kB/s | 28 kB 00:00
(34/686): perl-Sub-Quote-2.006006-8.el8.noarch.rpm 812 kB/s | 36 kB 00:00
(35/686): perl-Role-Tiny-2.002004-5.el8.noarch.rpm 725 kB/s | 39 kB 00:00
(36/686): perl-UUID-Tiny-1.04-25.el8.noarch.rpm 632 kB/s | 26 kB 00:00
(37/686): perl-aliased-0.34-21.el8.noarch.rpm 659 kB/s | 30 kB 00:00
(38/686): perl-strictures-2.000006-13.el8.noarch.rpm 779 kB/s | 35 kB 00:00
(39/686): screen-4.9.0-1.el8.x86_64.rpm 6.7 MB/s | 584 kB 00:00
(40/686): perl-Package-Stash-XS-0.28-17.el8.x86_64.rpm 83 kB/s | 38 kB 00:00
(41/686): perl-Devel-LexAlias-0.05-16.el8.x86_64.rpm 25 kB/s | 20 kB 00:00
(42/686): perl-Ref-Util-XS-0.117-2.el8.x86_64.rpm 57 kB/s | 26 kB 00:00
(43/686): perl-PadWalker-2.3-2.el8.x86_64.rpm 44 kB/s | 31 kB 00:00
(44/686): perl-Devel-Caller-2.06-15.el8.x86_64.rpm 13 kB/s | 23 kB 00:01
(45/686): perl-Variable-Magic-0.62-3.el8.x86_64.rpm 286 kB/s | 59 kB 00:00
(46/686): perl-Params-Validate-1.29-5.el8.x86_64.rpm 88 kB/s | 80 kB 00:00
(47/686): perl-Eval-Closure-0.14-5.el8.noarch.rpm 148 kB/s | 28 kB 00:00
(48/686): perl-Package-Stash-0.37-9.el8.noarch.rpm 136 kB/s | 42 kB 00:00
(49/686): perl-MIME-Types-2.17-3.el8.noarch.rpm 78 kB/s | 77 kB 00:00
(50/686): perl-Sub-Identify-0.14-6.el8.x86_64.rpm 8.0 kB/s | 29 kB 00:03
(51/686): perl-B-Hooks-EndOfScope-0.21-6.el8.noarch.rpm 53 kB/s | 42 kB 00:00
(52/686): perl-Module-Implementation-0.09-15.el8.noarch.rpm 22 kB/s | 24 kB 00:01
(53/686): perl-Params-ValidationCompiler-0.27-1.el8.noarch.rpm 57 kB/s | 38 kB 00:00
(54/686): perl-File-MimeInfo-0.28-7.el8.noarch.rpm 33 kB/s | 56 kB 00:01
(55/686): perl-Sub-Exporter-Progressive-0.001013-5.el8.noarch.rpm 45 kB/s | 25 kB 00:00
(56/686): perl-Digest-SHA1-2.13-23.el8.x86_64.rpm 76 kB/s | 57 kB 00:00
(57/686): perl-IO-Tty-1.12-11.el8.x86_64.rpm 256 kB/s | 48 kB 00:00
(58/686): perl-Import-Into-1.002005-7.el8.noarch.rpm 15 kB/s | 20 kB 00:01
(59/686): perl-namespace-autoclean-0.28-10.el8.noarch.rpm 119 kB/s | 32 kB 00:00
(60/686): perl-Devel-GlobalDestruction-0.14-5.el8.noarch.rpm 88 kB/s | 24 kB 00:00
(61/686): perl-File-BaseDir-0.08-1.el8.noarch.rpm 21 kB/s | 23 kB 00:01
(62/686): perl-Class-Data-Inheritable-0.08-27.el8.noarch.rpm 91 kB/s | 17 kB 00:00
(63/686): perltidy-20180220-1.el8.noarch.rpm 216 kB/s | 428 kB 00:01
(64/686): perl-Ref-Util-0.203-4.el8.noarch.rpm 66 kB/s | 27 kB 00:00
(65/686): perl-Dist-CheckConflicts-0.11-11.el8.noarch.rpm 42 kB/s | 27 kB 00:00
(66/686): perl-Exception-Class-1.44-2.el8.noarch.rpm 44 kB/s | 50 kB 00:01
(67/686): perl-Specio-0.42-2.el8.noarch.rpm 846 kB/s | 159 kB 00:00
(68/686): perl-Devel-StackTrace-2.03-2.el8.noarch.rpm 52 kB/s | 35 kB 00:00
(69/686): perl-Class-Method-Modifiers-2.12-8.el8.noarch.rpm 41 kB/s | 49 kB 00:01
(70/686): perl-namespace-clean-0.27-7.el8.noarch.rpm 192 kB/s | 37 kB 00:00
(71/686): perl-Capture-Tiny-0.46-4.el8.noarch.rpm 21 kB/s | 39 kB 00:01
(72/686): lzop-1.03-20.el8.x86_64.rpm 330 kB/s | 62 kB 00:00
(73/686): perl-File-DesktopEntry-0.22-7.el8.noarch.rpm 26 kB/s | 27 kB 00:01
(74/686): tcl-8.6.8-2.el8.x86_64.rpm 3.5 MB/s | 1.1 MB 00:00
(75/686): libfdt-1.6.0-1.el8.x86_64.rpm 25 kB/s | 32 kB 00:01
(76/686): libmodman-2.0.1-17.el8.x86_64.rpm 92 kB/s | 36 kB 00:00
(77/686): libproxy-0.4.15-5.2.el8.x86_64.rpm 240 kB/s | 74 kB 00:00
(78/686): libmetalink-0.1.3-7.el8.x86_64.rpm 107 kB/s | 32 kB 00:00
(79/686): libappstream-glib-0.7.14-3.el8.x86_64.rpm 912 kB/s | 338 kB 00:00
(80/686): libical-3.0.3-3.el8.x86_64.rpm 207 kB/s | 279 kB 00:01
(81/686): numad-0.5-26.20150602git.el8.x86_64.rpm 338 kB/s | 41 kB 00:00
(82/686): usbutils-010-3.el8.x86_64.rpm 1.0 MB/s | 108 kB 00:00
(83/686): fontpackages-filesystem-1.44-22.el8.noarch.rpm 67 kB/s | 16 kB 00:00
(84/686): perl-Date-Manip-6.60-2.el8.noarch.rpm 4.5 MB/s | 1.1 MB 00:00
(85/686): bzip2-1.0.6-26.el8.x86_64.rpm 172 kB/s | 60 kB 00:00
(86/686): libstemmer-0-10.585svn.el8.x86_64.rpm 771 kB/s | 73 kB 00:00
(87/686): bash-completion-2.7-5.el8.noarch.rpm 1.4 MB/s | 274 kB 00:00
(88/686): m4-1.4.18-7.el8.x86_64.rpm 1.0 MB/s | 223 kB 00:00
(89/686): expect-5.45.4-5.el8.x86_64.rpm 981 kB/s | 267 kB 00:00
(90/686): iw-4.14-5.el8.x86_64.rpm 281 kB/s | 90 kB 00:00
(91/686): xml-common-0.6.3-50.el8.noarch.rpm 291 kB/s | 39 kB 00:00
(92/686): mailcap-2.1.48-3.el8.noarch.rpm 265 kB/s | 39 kB 00:00
(93/686): mailx-12.5-29.el8.x86_64.rpm 1.6 MB/s | 257 kB 00:00
(94/686): libpciaccess-0.14-1.el8.x86_64.rpm 299 kB/s | 32 kB 00:00
(95/686): tmux-2.7-1.el8.x86_64.rpm 1.4 MB/s | 317 kB 00:00
(96/686): libtool-ltdl-2.4.6-25.el8.x86_64.rpm 261 kB/s | 58 kB 00:00
(97/686): glib-networking-2.56.1-1.1.el8.x86_64.rpm 1.3 MB/s | 155 kB 00:00
(98/686): redhat-indexhtml-8-7.el8.noarch.rpm 209 kB/s | 242 kB 00:01
(99/686): isns-utils-libs-0.99-1.el8.x86_64.rpm 1.2 MB/s | 105 kB 00:00
(100/686): gdk-pixbuf2-2.36.12-5.el8.x86_64.rpm 1.3 MB/s | 467 kB 00:00
(101/686): lsof-4.93.2-1.el8.x86_64.rpm 1.3 MB/s | 253 kB 00:00
(102/686): p11-kit-server-0.23.22-1.el8.x86_64.rpm 960 kB/s | 179 kB 00:00
(103/686): libicu-60.3-2.el8_1.x86_64.rpm 14 MB/s | 8.8 MB 00:00
(104/686): smartmontools-7.1-1.el8.x86_64.rpm 959 kB/s | 544 kB 00:00
(105/686): dejavu-fonts-common-2.35-7.el8.noarch.rpm 391 kB/s | 74 kB 00:00
(106/686): dejavu-serif-fonts-2.35-7.el8.noarch.rpm 2.0 MB/s | 805 kB 00:00
(107/686): userspace-rcu-0.10.1-4.el8.x86_64.rpm 1.0 MB/s | 101 kB 00:00
(108/686): libxslt-1.1.32-6.el8.x86_64.rpm 1.7 MB/s | 250 kB 00:00
(109/686): avahi-libs-0.7-20.el8.x86_64.rpm 487 kB/s | 62 kB 00:00
(110/686): dejavu-sans-mono-fonts-2.35-7.el8.noarch.rpm 3.1 MB/s | 447 kB 00:00
(111/686): avahi-glib-0.7-20.el8.x86_64.rpm 44 kB/s | 14 kB 00:00
(112/686): crda-3.18_2020.04.29-1.el8.noarch.rpm 193 kB/s | 24 kB 00:00
(113/686): python3-ply-3.9-9.el8.noarch.rpm 979 kB/s | 111 kB 00:00
(114/686): libxcrypt-devel-4.1.1-6.el8.x86_64.rpm 135 kB/s | 25 kB 00:00
(115/686): bolt-0.9.1-1.el8.x86_64.rpm 752 kB/s | 201 kB 00:00
(116/686): dejavu-sans-fonts-2.35-7.el8.noarch.rpm 5.8 MB/s | 1.5 MB 00:00
(117/686): keyutils-1.5.10-9.el8.x86_64.rpm 677 kB/s | 66 kB 00:00
(118/686): libsepol-devel-2.9-3.el8.x86_64.rpm 897 kB/s | 87 kB 00:00
(119/686): gsettings-desktop-schemas-3.32.0-6.el8.x86_64.rpm 3.0 MB/s | 633 kB 00:00
(120/686): quota-nls-4.04-14.el8.noarch.rpm 461 kB/s | 95 kB 00:00
(121/686): keyutils-libs-devel-1.5.10-9.el8.x86_64.rpm 129 kB/s | 48 kB 00:00
(122/686): redhat-logos-84.5-1.el8.x86_64.rpm 2.5 MB/s | 364 kB 00:00
(123/686): glusterfs-6.0-56.4.el8.x86_64.rpm 5.1 MB/s | 667 kB 00:00
(124/686): glusterfs-libs-6.0-56.4.el8.x86_64.rpm 3.5 MB/s | 418 kB 00:00
(125/686): iscsi-initiator-utils-iscsiuio-6.2.1.4-4.git095f59c.el8.x86_64.rpm 1.1 MB/s | 100 kB 00:00
(126/686): freeipmi-1.6.8-1.el8.x86_64.rpm 7.4 MB/s | 2.1 MB 00:00
(127/686): iscsi-initiator-utils-6.2.1.4-4.git095f59c.el8.x86_64.rpm 1.4 MB/s | 378 kB 00:00
(128/686): cyrus-sasl-plain-2.1.27-6.el8_5.x86_64.rpm 254 kB/s | 48 kB 00:00
(129/686): mobile-broadband-provider-info-20210805-1.el8.noarch.rpm 196 kB/s | 77 kB 00:00
(130/686): cyrus-sasl-2.1.27-6.el8_5.x86_64.rpm 442 kB/s | 96 kB 00:00
(131/686): quota-4.04-14.el8.x86_64.rpm 2.3 MB/s | 214 kB 00:00
(132/686): cyrus-sasl-gssapi-2.1.27-6.el8_5.x86_64.rpm 505 kB/s | 50 kB 00:00
(133/686): glusterfs-client-xlators-6.0-56.4.el8.x86_64.rpm 6.2 MB/s | 883 kB 00:00
(134/686): fontconfig-2.13.1-4.el8.x86_64.rpm 1.1 MB/s | 274 kB 00:00
(135/686): cyrus-sasl-md5-2.1.27-6.el8_5.x86_64.rpm 272 kB/s | 66 kB 00:00
(136/686): wpa_supplicant-2.10-1.el8.x86_64.rpm 8.8 MB/s | 2.1 MB 00:00
(137/686): syslinux-nonlinux-6.04-6.el8.noarch.rpm 2.9 MB/s | 555 kB 00:00
(138/686): pcre2-utf32-10.32-3.el8_6.x86_64.rpm 913 kB/s | 220 kB 00:00
(139/686): postfix-3.5.8-4.el8.x86_64.rpm 6.1 MB/s | 1.5 MB 00:00
(140/686): fuse-common-3.3.0-16.el8.x86_64.rpm 255 kB/s | 22 kB 00:00
(141/686): pcre2-devel-10.32-3.el8_6.x86_64.rpm 5.4 MB/s | 605 kB 00:00
(142/686): pcre2-utf16-10.32-3.el8_6.x86_64.rpm 2.0 MB/s | 229 kB 00:00
(143/686): bluez-obexd-5.63-1.el8.x86_64.rpm 1.4 MB/s | 233 kB 00:00
(144/686): syslinux-6.04-6.el8.x86_64.rpm 3.4 MB/s | 578 kB 00:00
(145/686): rsync-3.1.3-19.el8_7.1.x86_64.rpm 1.5 MB/s | 410 kB 00:00
(146/686): mtools-4.0.18-15.el8_6.x86_64.rpm 382 kB/s | 213 kB 00:00
(147/686): openssl-devel-1.1.1k-9.el8_7.x86_64.rpm 8.8 MB/s | 2.3 MB 00:00
(148/686): strace-5.18-2.el8.x86_64.rpm 5.3 MB/s | 1.4 MB 00:00
(149/686): libverto-devel-0.3.2-2.el8.x86_64.rpm 68 kB/s | 18 kB 00:00
(150/686): fuse-2.9.7-16.el8.x86_64.rpm 432 kB/s | 83 kB 00:00
(151/686): libcom_err-devel-1.45.6-5.el8.x86_64.rpm 206 kB/s | 39 kB 00:00
(152/686): gssproxy-0.8.0-21.el8.x86_64.rpm 604 kB/s | 119 kB 00:00
(153/686): bluez-libs-5.63-1.el8.x86_64.rpm 1.2 MB/s | 114 kB 00:00
(154/686): rpcbind-1.2.5-10.el8.x86_64.rpm 739 kB/s | 70 kB 00:00
(155/686): bluez-5.63-1.el8.x86_64.rpm 3.7 MB/s | 1.4 MB 00:00
(156/686): libqb-1.0.3-13.el8_7.x86_64.rpm 1.3 MB/s | 113 kB 00:00
(157/686): zlib-devel-1.2.11-21.el8_7.x86_64.rpm 460 kB/s | 58 kB 00:00
(158/686): elfutils-libelf-devel-0.188-3.el8.x86_64.rpm 329 kB/s | 61 kB 00:00
(159/686): cups-libs-2.2.6-51.el8.x86_64.rpm 2.3 MB/s | 435 kB 00:00
(160/686): samba-client-libs-4.17.5-2.el8.x86_64.rpm 12 MB/s | 5.0 MB 00:00
(161/686): libwbclient-4.17.5-2.el8.x86_64.rpm 668 kB/s | 125 kB 00:00
(162/686): python3-setuptools-39.2.0-7.el8.noarch.rpm 811 kB/s | 163 kB 00:00
(163/686): binutils-2.30-119.el8.x86_64.rpm 7.2 MB/s | 5.8 MB 00:00
(164/686): glibc-headers-2.28-225.el8.x86_64.rpm 1.8 MB/s | 488 kB 00:00
(165/686): nfs-utils-2.3.3-59.el8.x86_64.rpm 1.9 MB/s | 515 kB 00:00
(166/686): augeas-1.12.0-8.el8.x86_64.rpm 473 kB/s | 57 kB 00:00
(167/686): libatomic-8.5.0-18.el8.x86_64.rpm 200 kB/s | 25 kB 00:00
(168/686): device-mapper-multipath-libs-0.8.4-37.el8.x86_64.rpm 2.7 MB/s | 334 kB 00:00
(169/686): net-snmp-libs-5.8-27.el8.x86_64.rpm 5.0 MB/s | 827 kB 00:00
(170/686): libselinux-devel-2.9-8.el8.x86_64.rpm 1.8 MB/s | 200 kB 00:00
(171/686): dhcp-libs-4.3.6-49.el8.x86_64.rpm 1.5 MB/s | 148 kB 00:00
(172/686): samba-common-4.17.5-2.el8.noarch.rpm 2.5 MB/s | 230 kB 00:00
(173/686): nvme-cli-1.16-7.el8.x86_64.rpm 1.8 MB/s | 503 kB 00:00
(174/686): libsoup-2.62.3-3.el8.x86_64.rpm 988 kB/s | 425 kB 00:00
(175/686): glibc-devel-2.28-225.el8.x86_64.rpm 856 kB/s | 83 kB 00:00
(176/686): device-mapper-multipath-0.8.4-37.el8.x86_64.rpm 1.1 MB/s | 208 kB 00:00
(177/686): augeas-libs-1.12.0-8.el8.x86_64.rpm 1.1 MB/s | 437 kB 00:00
(178/686): yum-utils-4.0.21-19.el8_8.noarch.rpm 763 kB/s | 75 kB 00:00
(179/686): samba-common-libs-4.17.5-2.el8.x86_64.rpm 946 kB/s | 180 kB 00:00
(180/686): dhcp-server-4.3.6-49.el8.x86_64.rpm 2.0 MB/s | 530 kB 00:00
(181/686): dhcp-common-4.3.6-49.el8.noarch.rpm 920 kB/s | 207 kB 00:00
(182/686): libsmbclient-4.17.5-2.el8.x86_64.rpm 509 kB/s | 153 kB 00:00
(183/686): ModemManager-glib-1.20.2-1.el8.x86_64.rpm 1.8 MB/s | 338 kB 00:00
(184/686): librdmacm-44.0-2.el8.1.x86_64.rpm 392 kB/s | 78 kB 00:00
(185/686): emacs-filesystem-26.1-10.el8_8.2.noarch.rpm 366 kB/s | 70 kB 00:00
(186/686): krb5-devel-1.18.2-25.el8_8.x86_64.rpm 2.7 MB/s | 562 kB 00:00
(187/686): libkadm5-1.18.2-25.el8_8.x86_64.rpm 1.0 MB/s | 188 kB 00:00
(188/686): glibc-all-langpacks-2.28-225.el8.x86_64.rpm 14 MB/s | 26 MB 00:01
(189/686): iproute-tc-5.18.0-1.1.el8_8.x86_64.rpm 4.3 MB/s | 466 kB 00:00
(190/686): NetworkManager-wifi-1.40.16-3.el8_8.x86_64.rpm 592 kB/s | 201 kB 00:00
(191/686): NetworkManager-initscripts-updown-1.40.16-3.el8_8.noarch.rpm 1.4 MB/s | 143 kB 00:00
(192/686): systemd-container-239-74.el8_8.2.x86_64.rpm 2.1 MB/s | 773 kB 00:00
(193/686): bind-export-libs-9.11.36-8.el8_8.1.x86_64.rpm 2.2 MB/s | 1.1 MB 00:00
(194/686): kernel-headers-4.18.0-477.15.1.el8_8.x86_64.rpm 9.1 MB/s | 11 MB 00:01
(195/686): python3-pexpect-4.3.1-3.el8.noarch.rpm 738 kB/s | 138 kB 00:00
(196/686): perl-CGI-4.38-2.el8.noarch.rpm 584 kB/s | 208 kB 00:00
(197/686): perl-JSON-2.97.001-2.el8.noarch.rpm 513 kB/s | 96 kB 00:00
(198/686): perl-XML-SAX-1.00-1.el8.noarch.rpm 709 kB/s | 65 kB 00:00
(199/686): perl-Text-Unidecode-1.30-5.el8.noarch.rpm 796 kB/s | 149 kB 00:00
(200/686): perl-MailTools-2.20-2.el8.noarch.rpm 80 kB/s | 113 kB 00:01
(201/686): python3-ptyprocess-0.5.2-4.el8.noarch.rpm 114 kB/s | 31 kB 00:00
(202/686): kernel-devel-4.18.0-477.15.1.el8_8.x86_64.rpm 8.7 MB/s | 23 MB 00:02
(203/686): urw-base35-p052-fonts-20170801-10.el8.noarch.rpm 2.1 MB/s | 982 kB 00:00
(204/686): iso-codes-3.79-2.el8.noarch.rpm 5.7 MB/s | 3.4 MB 00:00
(205/686): perl-XML-Simple-2.25-1.el8.noarch.rpm 455 kB/s | 87 kB 00:00
(206/686): urw-base35-gothic-fonts-20170801-10.el8.noarch.rpm 1.8 MB/s | 654 kB 00:00
(207/686): libquvi-scripts-0.9.20131130-9.el8.noarch.rpm 255 kB/s | 110 kB 00:00
(208/686): urw-base35-fonts-20170801-10.el8.noarch.rpm 72 kB/s | 12 kB 00:00
(209/686): geolite2-country-20180605-1.el8.noarch.rpm 3.6 MB/s | 1.0 MB 00:00
(210/686): geolite2-city-20180605-1.el8.noarch.rpm 9.9 MB/s | 19 MB 00:01
(211/686): color-filesystem-1-20.el8.noarch.rpm 15 kB/s | 11 kB 00:00
(212/686): perl-Module-Runtime-0.016-2.el8.noarch.rpm 21 kB/s | 26 kB 00:01
(213/686): sound-theme-freedesktop-0.8-9.el8.noarch.rpm 527 kB/s | 382 kB 00:00
(214/686): system-config-printer-libs-1.5.11-13.el8.noarch.rpm 693 kB/s | 865 kB 00:01
(215/686): hunspell-en-0.20140811.1-12.el8.noarch.rpm 1.0 MB/s | 200 kB 00:00
(216/686): google-droid-sans-fonts-20120715-13.el8.noarch.rpm 11 MB/s | 2.5 MB 00:00
(217/686): urw-base35-bookman-fonts-20170801-10.el8.noarch.rpm 3.9 MB/s | 857 kB 00:00
(218/686): python3-argcomplete-1.9.3-6.el8.noarch.rpm 322 kB/s | 60 kB 00:00
(219/686): urw-base35-fonts-common-20170801-10.el8.noarch.rpm 125 kB/s | 23 kB 00:00
(220/686): lua-json-1.3.2-9.el8.noarch.rpm 24 kB/s | 29 kB 00:01
(221/686): urw-base35-d050000l-fonts-20170801-10.el8.noarch.rpm 868 kB/s | 79 kB 00:00
(222/686): urw-base35-c059-fonts-20170801-10.el8.noarch.rpm 5.3 MB/s | 884 kB 00:00
(223/686): urw-base35-nimbus-mono-ps-fonts-20170801-10.el8.noarch.rpm 3.6 MB/s | 801 kB 00:00
(224/686): perl-Authen-SASL-2.16-13.el8.noarch.rpm 50 kB/s | 57 kB 00:01
(225/686): adobe-mappings-cmap-deprecated-20171205-3.el8.noarch.rpm 621 kB/s | 119 kB 00:00
(226/686): hunspell-en-GB-0.20140811.1-12.el8.noarch.rpm 498 kB/s | 245 kB 00:00
(227/686): perl-Net-SMTP-SSL-1.04-5.el8.noarch.rpm 75 kB/s | 15 kB 00:00
(228/686): libavc1394-0.5.4-7.el8.x86_64.rpm 307 kB/s | 61 kB 00:00
(229/686): adobe-mappings-pdf-20180407-1.el8.noarch.rpm 3.6 MB/s | 707 kB 00:00
(230/686): hicolor-icon-theme-0.17-2.el8.noarch.rpm 254 kB/s | 48 kB 00:00
(231/686): hunspell-en-US-0.20140811.1-12.el8.noarch.rpm 293 kB/s | 196 kB 00:00
(232/686): adobe-mappings-cmap-20171205-3.el8.noarch.rpm 6.9 MB/s | 2.1 MB 00:00
(233/686): urw-base35-nimbus-sans-fonts-20170801-10.el8.noarch.rpm 4.1 MB/s | 1.3 MB 00:00
(234/686): urw-base35-standard-symbols-ps-fonts-20170801-10.el8.noarch.rpm 427 kB/s | 44 kB 00:00
(235/686): lcms2-2.9-2.el8.x86_64.rpm 1.3 MB/s | 165 kB 00:00
(236/686): urw-base35-nimbus-roman-fonts-20170801-10.el8.noarch.rpm 5.8 MB/s | 865 kB 00:00
(237/686): urw-base35-z003-fonts-20170801-10.el8.noarch.rpm 1.9 MB/s | 279 kB 00:00
(238/686): perl-XML-NamespaceSupport-1.12-4.el8.noarch.rpm 232 kB/s | 30 kB 00:00
(239/686): perl-XML-SAX-Base-1.09-4.el8.noarch.rpm 390 kB/s | 35 kB 00:00
(240/686): perl-XML-LibXML-2.0132-2.el8.x86_64.rpm 1.6 MB/s | 372 kB 00:00
(241/686): libusal-1.1.11-39.el8.x86_64.rpm 732 kB/s | 145 kB 00:00
(242/686): libXxf86misc-1.0.4-1.el8.x86_64.rpm 123 kB/s | 23 kB 00:00
(243/686): jbigkit-libs-2.1-14.el8.x86_64.rpm 273 kB/s | 55 kB 00:00
(244/686): libmcpp-2.7.2-20.el8.x86_64.rpm 417 kB/s | 81 kB 00:00
(245/686): libtheora-1.1.1-21.el8.x86_64.rpm 858 kB/s | 184 kB 00:00
(246/686): pinentry-gtk-1.1.0-2.el8.x86_64.rpm 633 kB/s | 54 kB 00:00
(247/686): libXtst-1.2.3-7.el8.x86_64.rpm 239 kB/s | 22 kB 00:00
(248/686): lua-expat-1.3.0-12.el8.1.x86_64.rpm 177 kB/s | 38 kB 00:00
(249/686): xorg-x11-server-utils-7.7-27.el8.x86_64.rpm 968 kB/s | 197 kB 00:00
(250/686): flac-libs-1.3.2-9.el8.x86_64.rpm 896 kB/s | 217 kB 00:00
(251/686): libXinerama-1.1.4-1.el8.x86_64.rpm 216 kB/s | 16 kB 00:00
(252/686): genisoimage-1.1.11-39.el8.x86_64.rpm 1.5 MB/s | 316 kB 00:00
(253/686): totem-pl-parser-3.26.1-2.el8.x86_64.rpm 118 kB/s | 194 kB 00:01
(254/686): perl-NetAddr-IP-4.079-7.el8.x86_64.rpm 511 kB/s | 132 kB 00:00
(255/686): libdvdnav-5.0.3-8.el8.x86_64.rpm 561 kB/s | 61 kB 00:00
(256/686): celt051-0.5.1.3-15.el8.x86_64.rpm 415 kB/s | 63 kB 00:00
(257/686): startup-notification-0.12-15.el8.x86_64.rpm 71 kB/s | 45 kB 00:00
(258/686): liboauth-1.0.3-9.el8.x86_64.rpm 287 kB/s | 29 kB 00:00
(259/686): libiec61883-1.2.0-18.el8.x86_64.rpm 254 kB/s | 43 kB 00:00
(260/686): at-spi2-core-2.28.0-1.el8.x86_64.rpm 482 kB/s | 169 kB 00:00
(261/686): libev-4.24-6.el8.x86_64.rpm 277 kB/s | 52 kB 00:00
(262/686): gnome-keyring-pam-3.28.2-1.el8.x86_64.rpm 250 kB/s | 47 kB 00:00
(263/686): libsrtp-1.5.4-8.el8.x86_64.rpm 295 kB/s | 282 kB 00:00
(264/686): graphite2-1.3.10-10.el8.x86_64.rpm 642 kB/s | 122 kB 00:00
(265/686): libXcursor-1.1.15-3.el8.x86_64.rpm 381 kB/s | 36 kB 00:00
(266/686): perl-Socket6-0.28-6.el8.x86_64.rpm 35 kB/s | 36 kB 00:01
(267/686): libogg-1.3.2-10.el8.x86_64.rpm 162 kB/s | 31 kB 00:00
(268/686): at-spi2-atk-2.26.2-1.el8.x86_64.rpm 471 kB/s | 89 kB 00:00
(269/686): switcheroo-control-1.1-5.el8.x86_64.rpm 65 kB/s | 30 kB 00:00
(270/686): speexdsp-1.2-0.13.rc3.el8.x86_64.rpm 577 kB/s | 456 kB 00:00
(271/686): rtkit-0.11-19.el8.x86_64.rpm 303 kB/s | 61 kB 00:00
(272/686): mcpp-2.7.2-20.el8.x86_64.rpm 162 kB/s | 31 kB 00:00
(273/686): taglib-1.11.1-8.el8.x86_64.rpm 845 kB/s | 340 kB 00:00
(274/686): librbd1-12.2.7-9.el8.x86_64.rpm 2.6 MB/s | 1.1 MB 00:00
(275/686): libXfont2-2.0.3-2.el8.x86_64.rpm 335 kB/s | 149 kB 00:00
(276/686): colord-gtk-0.1.26-8.el8.x86_64.rpm 316 kB/s | 34 kB 00:00
(277/686): cogl-1.22.2-10.el8.x86_64.rpm 2.5 MB/s | 478 kB 00:00
(278/686): libimobiledevice-1.2.0-16.el8.x86_64.rpm 147 kB/s | 80 kB 00:00
(279/686): libSM-1.2.3-1.el8.x86_64.rpm 250 kB/s | 48 kB 00:00
(280/686): libxklavier-5.4-11.el8.x86_64.rpm 145 kB/s | 71 kB 00:00
(281/686): libidn-1.34-5.el8.x86_64.rpm 1.0 MB/s | 239 kB 00:00
(282/686): libgnomekbd-3.26.0-4.el8.x86_64.rpm 789 kB/s | 168 kB 00:00
(283/686): adwaita-gtk2-theme-3.22.3-4.el8.x86_64.rpm 618 kB/s | 132 kB 00:00
(284/686): hyphen-2.8.8-9.el8.x86_64.rpm 158 kB/s | 33 kB 00:00
(285/686): librados2-12.2.7-9.el8.x86_64.rpm 5.6 MB/s | 2.9 MB 00:00
(286/686): libXfixes-5.0.3-7.el8.x86_64.rpm 203 kB/s | 25 kB 00:00
(287/686): lua-lpeg-1.0.1-6.el8.x86_64.rpm 665 kB/s | 67 kB 00:00
(288/686): libgtop2-2.38.0-3.el8.x86_64.rpm 229 kB/s | 142 kB 00:00
(289/686): linuxconsoletools-1.6.0-4.el8.x86_64.rpm 389 kB/s | 82 kB 00:00
(290/686): libshout-2.2.2-19.el8.x86_64.rpm 571 kB/s | 50 kB 00:00
(291/686): xorg-x11-drv-vesa-2.4.0-3.el8.x86_64.rpm 73 kB/s | 31 kB 00:00
(292/686): libXxf86vm-1.1.4-9.el8.x86_64.rpm 139 kB/s | 19 kB 00:00
(293/686): libdv-1.0.0-27.el8.x86_64.rpm 750 kB/s | 85 kB 00:00
(294/686): xcb-util-0.4.0-10.el8.x86_64.rpm 176 kB/s | 22 kB 00:00
(295/686): perl-Text-Soundex-3.05-8.el8.x86_64.rpm 276 kB/s | 32 kB 00:00
(296/686): xorg-x11-drv-fbdev-0.5.0-2.el8.x86_64.rpm 212 kB/s | 27 kB 00:00
(297/686): speex-1.2.0-1.el8.x86_64.rpm 411 kB/s | 71 kB 00:00
(298/686): xorg-x11-xinit-1.3.4-18.el8.x86_64.rpm 241 kB/s | 58 kB 00:00
(299/686): libthai-0.1.27-2.el8.x86_64.rpm 654 kB/s | 203 kB 00:00
(300/686): opus-1.3-0.4.beta.el8.x86_64.rpm 924 kB/s | 204 kB 00:00
(301/686): colord-libs-1.4.2-1.el8.x86_64.rpm 2.1 MB/s | 236 kB 00:00
(302/686): libijs-0.35-5.el8.x86_64.rpm 314 kB/s | 30 kB 00:00
(303/686): libXdamage-1.1.4-14.el8.x86_64.rpm 141 kB/s | 27 kB 00:00
(304/686): clutter-gtk-1.8.4-3.el8.x86_64.rpm 163 kB/s | 53 kB 00:00
(305/686): rest-0.8.1-2.el8.x86_64.rpm 332 kB/s | 71 kB 00:00
(306/686): libdvdread-5.0.3-9.el8.x86_64.rpm 847 kB/s | 75 kB 00:00
(307/686): sbc-1.3-9.el8.x86_64.rpm 247 kB/s | 65 kB 00:00
(308/686): GConf2-3.2.6-22.el8.x86_64.rpm 3.5 MB/s | 1.0 MB 00:00
(309/686): harfbuzz-1.7.5-3.el8.x86_64.rpm 1.4 MB/s | 294 kB 00:00
(310/686): clutter-gst3-3.0.26-1.el8.x86_64.rpm 419 kB/s | 82 kB 00:00
(311/686): libpaper-1.1.24-22.el8.x86_64.rpm 470 kB/s | 45 kB 00:00
(312/686): libXcomposite-0.4.4-14.el8.x86_64.rpm 217 kB/s | 29 kB 00:00
(313/686): perl-XML-Parser-2.44-11.el8.x86_64.rpm 1.2 MB/s | 226 kB 00:00
(314/686): libfontenc-1.1.3-8.el8.x86_64.rpm 154 kB/s | 37 kB 00:00
(315/686): libusbmuxd-1.0.10-9.el8.x86_64.rpm 365 kB/s | 35 kB 00:00
(316/686): libasyncns-0.8-14.el8.x86_64.rpm 47 kB/s | 32 kB 00:00
(317/686): lua-socket-3.0-0.17.rc1.el8.x86_64.rpm 115 kB/s | 184 kB 00:01
(318/686): gnome-themes-standard-3.22.3-4.el8.x86_64.rpm 3.5 MB/s | 2.7 MB 00:00
(319/686): libXrender-0.9.10-7.el8.x86_64.rpm 83 kB/s | 33 kB 00:00
(320/686): lame-libs-3.100-6.el8.x86_64.rpm 1.6 MB/s | 361 kB 00:00
(321/686): mpg123-libs-1.25.10-2.el8.x86_64.rpm 975 kB/s | 208 kB 00:00
(322/686): hunspell-1.6.2-1.el8.x86_64.rpm 1.7 MB/s | 331 kB 00:00
(323/686): atk-2.28.1-1.el8.x86_64.rpm 1.2 MB/s | 272 kB 00:00
(324/686): libdatrie-0.2.9-7.el8.x86_64.rpm 137 kB/s | 33 kB 00:00
(325/686): libraw1394-2.1.2-5.el8.x86_64.rpm 380 kB/s | 72 kB 00:00
(326/686): gtksourceview3-3.24.9-1.el8.x86_64.rpm 2.4 MB/s | 605 kB 00:00
(327/686): harfbuzz-icu-1.7.5-3.el8.x86_64.rpm 126 kB/s | 24 kB 00:00
(328/686): libxshmfence-1.3-2.el8.x86_64.rpm 31 kB/s | 13 kB 00:00
(329/686): isl-0.16.1-6.el8.x86_64.rpm 3.0 MB/s | 841 kB 00:00
(330/686): gsm-1.0.17-5.el8.x86_64.rpm 145 kB/s | 37 kB 00:00
(331/686): libquvi-0.9.4-12.el8.x86_64.rpm 467 kB/s | 92 kB 00:00
(332/686): bison-3.0.4-10.el8.x86_64.rpm 3.2 MB/s | 688 kB 00:00
(333/686): cups-pk-helper-0.2.6-5.el8.x86_64.rpm 405 kB/s | 91 kB 00:00
(334/686): colord-1.4.2-1.el8.x86_64.rpm 1.0 MB/s | 494 kB 00:00
(335/686): iio-sensor-proxy-2.4-3.el8.x86_64.rpm 244 kB/s | 54 kB 00:00
(336/686): xorg-x11-xauth-1.0.9-12.el8.x86_64.rpm 35 kB/s | 39 kB 00:01
(337/686): libXv-1.0.11-7.el8.x86_64.rpm 25 kB/s | 20 kB 00:00
(338/686): mtdev-1.1.5-12.el8.x86_64.rpm 39 kB/s | 24 kB 00:00
(339/686): python3-cairo-1.16.3-6.el8.x86_64.rpm 421 kB/s | 90 kB 00:00
(340/686): python3-cups-1.9.72-21.el8.x86_64.rpm 451 kB/s | 86 kB 00:00
(341/686): gcr-3.28.0-1.el8.x86_64.rpm 682 kB/s | 692 kB 00:01
(342/686): libplist-2.0.0-10.el8.x86_64.rpm 352 kB/s | 77 kB 00:00
(343/686): libv4l-1.14.2-3.el8.x86_64.rpm 741 kB/s | 195 kB 00:00
(344/686): libXt-1.1.5-12.el8.x86_64.rpm 1.8 MB/s | 185 kB 00:00
(345/686): flex-2.6.1-9.el8.x86_64.rpm 2.1 MB/s | 320 kB 00:00
(346/686): libvorbis-1.3.6-2.el8.x86_64.rpm 752 kB/s | 196 kB 00:00
(347/686): libssh2-1.8.0-8.module+el8.0.0+4084+cceb9f44.1.x86_64.rpm 292 kB/s | 99 kB 00:00
(348/686): gnome-keyring-3.28.2-1.el8.x86_64.rpm 970 kB/s | 931 kB 00:00
(349/686): perl-String-ShellQuote-1.04-24.module+el8.1.0+2942+5e3df93c.noarch.rpm 77 kB/s | 23 kB 00:00
(350/686): gdk-pixbuf2-modules-2.36.12-5.el8.x86_64.rpm 332 kB/s | 109 kB 00:00
(351/686): libICE-1.0.9-15.el8.x86_64.rpm 606 kB/s | 74 kB 00:00
(352/686): perl-Convert-ASN1-0.27-17.el8.noarch.rpm 624 kB/s | 60 kB 00:00
(353/686): python3-pycurl-7.43.0.2-4.el8.x86_64.rpm 1.2 MB/s | 227 kB 00:00
(354/686): libcacard-2.7.0-2.el8_1.x86_64.rpm 66 kB/s | 52 kB 00:00
(355/686): gstreamer1-plugins-bad-free-1.16.1-1.el8.x86_64.rpm 3.5 MB/s | 1.8 MB 00:00
(356/686): libpmem-1.6.1-1.el8.x86_64.rpm 373 kB/s | 79 kB 00:00
(357/686): libxcb-1.13.1-1.el8.x86_64.rpm 1.2 MB/s | 229 kB 00:00
(358/686): orc-0.4.28-3.el8.x86_64.rpm 928 kB/s | 175 kB 00:00
(359/686): gstreamer1-1.16.1-2.el8.x86_64.rpm 2.3 MB/s | 1.3 MB 00:00
(360/686): perl-LDAP-0.66-7.el8.noarch.rpm 568 kB/s | 386 kB 00:00
(361/686): libxkbcommon-x11-0.9.1-1.el8.x86_64.rpm 87 kB/s | 25 kB 00:00
(362/686): gvnc-0.9.0-2.el8.x86_64.rpm 1.0 MB/s | 102 kB 00:00
(363/686): xorg-x11-drv-libinput-0.29.0-1.el8.x86_64.rpm 287 kB/s | 50 kB 00:00
(364/686): perl-HTML-Parser-3.72-15.module+el8.3.0+6498+9eecfe51.x86_64.rpm 630 kB/s | 119 kB 00:00
(365/686): gtk-vnc2-0.9.0-2.el8.x86_64.rpm 91 kB/s | 49 kB 00:00
(366/686): perl-LWP-MediaTypes-6.02-15.module+el8.3.0+6498+9eecfe51.noarch.rpm 301 kB/s | 29 kB 00:00
(367/686): perl-TimeDate-2.30-15.module+el8.3.0+6498+9eecfe51.noarch.rpm 264 kB/s | 53 kB 00:00
(368/686): python3-gobject-3.28.3-2.el8.x86_64.rpm 261 kB/s | 26 kB 00:00
(369/686): perl-Net-HTTP-6.17-2.module+el8.3.0+6498+9eecfe51.noarch.rpm 230 kB/s | 43 kB 00:00
(370/686): perl-Data-Dump-1.23-7.module+el8.3.0+6498+9eecfe51.noarch.rpm 76 kB/s | 37 kB 00:00
(371/686): perl-HTTP-Date-6.02-19.module+el8.3.0+6498+9eecfe51.noarch.rpm 102 kB/s | 19 kB 00:00
(372/686): perl-WWW-RobotRules-6.02-18.module+el8.3.0+6498+9eecfe51.noarch.rpm 113 kB/s | 23 kB 00:00
(373/686): perl-HTTP-Message-6.18-1.module+el8.3.0+6498+9eecfe51.noarch.rpm 1.2 MB/s | 100 kB 00:00
(374/686): clutter-1.26.2-8.el8.x86_64.rpm 967 kB/s | 1.1 MB 00:01
(375/686): perl-IO-HTML-1.001-11.module+el8.3.0+6498+9eecfe51.noarch.rpm 256 kB/s | 28 kB 00:00
(376/686): perl-NTLM-1.09-17.module+el8.3.0+6498+9eecfe51.noarch.rpm 256 kB/s | 24 kB 00:00
(377/686): perl-libwww-perl-6.34-1.module+el8.3.0+6498+9eecfe51.noarch.rpm 1.9 MB/s | 213 kB 00:00
(378/686): perl-Digest-HMAC-1.03-17.module+el8.3.0+6498+9eecfe51.noarch.rpm 181 kB/s | 20 kB 00:00
(379/686): perl-HTML-Tagset-3.20-34.module+el8.3.0+6498+9eecfe51.noarch.rpm 235 kB/s | 24 kB 00:00
(380/686): perl-HTTP-Cookies-6.04-2.module+el8.3.0+6498+9eecfe51.noarch.rpm 146 kB/s | 39 kB 00:00
(381/686): perl-File-Listing-6.04-17.module+el8.3.0+6498+9eecfe51.noarch.rpm 146 kB/s | 18 kB 00:00
(382/686): perl-Try-Tiny-0.30-7.module+el8.3.0+6498+9eecfe51.noarch.rpm 471 kB/s | 45 kB 00:00
(383/686): vte291-0.52.4-2.el8.x86_64.rpm 2.4 MB/s | 256 kB 00:00
(384/686): autogen-libopts-5.18.12-8.el8.x86_64.rpm 876 kB/s | 75 kB 00:00
(385/686): perl-HTTP-Negotiate-6.01-19.module+el8.3.0+6498+9eecfe51.noarch.rpm 74 kB/s | 22 kB 00:00
(386/686): pipewire-0.3.6-1.el8.x86_64.rpm 571 kB/s | 108 kB 00:00
(387/686): libXext-1.3.4-1.el8.x86_64.rpm 166 kB/s | 45 kB 00:00
(388/686): libmaxminddb-1.2.0-10.el8.x86_64.rpm 177 kB/s | 33 kB 00:00
(389/686): perl-DBD-Pg-3.7.4-4.module+el8.3.0+6565+907cf59b.x86_64.rpm 330 kB/s | 215 kB 00:00
(390/686): libXi-1.7.10-1.el8.x86_64.rpm 198 kB/s | 49 kB 00:00
(391/686): libXdmcp-1.1.3-1.el8.x86_64.rpm 216 kB/s | 41 kB 00:00
(392/686): librsvg2-2.42.7-4.el8.x86_64.rpm 2.2 MB/s | 555 kB 00:00
(393/686): libXrandr-1.5.2-1.el8.x86_64.rpm 169 kB/s | 34 kB 00:00
(394/686): bpg-dejavu-sans-fonts-2.28-11.el8.noarch.rpm 60 kB/s | 38 kB 00:00
(395/686): libXft-2.3.3-1.el8.x86_64.rpm 345 kB/s | 67 kB 00:00
(396/686): xorg-x11-xkb-utils-7.7-28.el8.x86_64.rpm 1.2 MB/s | 114 kB 00:00
(397/686): bpg-fonts-common-20120413-11.el8.noarch.rpm 36 kB/s | 23 kB 00:00
(398/686): libvpx-1.7.0-8.el8.x86_64.rpm 4.3 MB/s | 854 kB 00:00
(399/686): libXau-1.0.9-3.el8.x86_64.rpm 416 kB/s | 37 kB 00:00
(400/686): glx-utils-8.4.0-5.20181118git1830dcb.el8.x86_64.rpm 486 kB/s | 44 kB 00:00
(401/686): libxkbfile-1.1.0-1.el8.x86_64.rpm 828 kB/s | 88 kB 00:00
(402/686): pipewire-libs-0.3.6-1.el8.x86_64.rpm 4.2 MB/s | 712 kB 00:00
(403/686): drpm-0.4.1-3.el8.x86_64.rpm 501 kB/s | 68 kB 00:00
(404/686): libXmu-1.1.3-1.el8.x86_64.rpm 399 kB/s | 75 kB 00:00
(405/686): perl-Mail-Sender-0.903-7.el8.noarch.rpm 68 kB/s | 57 kB 00:00
(406/686): libvirt-glib-3.0.0-1.el8.x86_64.rpm 343 kB/s | 104 kB 00:00
(407/686): vte-profile-0.52.4-2.el8.x86_64.rpm 55 kB/s | 15 kB 00:00
(408/686): nodejs-full-i18n-10.24.0-1.module+el8.3.0+10166+b07ac28e.x86_64.rpm 7.0 MB/s | 7.3 MB 00:01
(409/686): nodejs-10.24.0-1.module+el8.3.0+10166+b07ac28e.x86_64.rpm 8.3 MB/s | 8.8 MB 00:01
(410/686): abattis-cantarell-fonts-0.0.25-6.el8.noarch.rpm 693 kB/s | 156 kB 00:00
(411/686): npm-6.14.11-1.10.24.0.1.module+el8.3.0+10166+b07ac28e.x86_64.rpm 3.5 MB/s | 3.7 MB 00:01
(412/686): gpm-1.20.7-17.el8.x86_64.rpm 878 kB/s | 200 kB 00:00
(413/686): osinfo-db-tools-1.9.0-1.el8.x86_64.rpm 312 kB/s | 68 kB 00:00
(414/686): gnome-bluetooth-3.34.3-1.el8.x86_64.rpm 256 kB/s | 60 kB 00:00
(415/686): libcanberra-gtk3-0.30-18.el8.x86_64.rpm 101 kB/s | 39 kB 00:00
(416/686): gjs-1.56.2-5.el8.x86_64.rpm 2.2 MB/s | 425 kB 00:00
(417/686): gnome-terminal-3.28.3-3.el8.x86_64.rpm 3.4 MB/s | 1.3 MB 00:00
(418/686): libcanberra-0.30-18.el8.x86_64.rpm 214 kB/s | 93 kB 00:00
(419/686): twolame-libs-0.3.13-12.el8.x86_64.rpm 583 kB/s | 57 kB 00:00
(420/686): libmpc-1.1.0-9.1.el8.x86_64.rpm 674 kB/s | 61 kB 00:00
(421/686): enchant2-2.2.3-3.el8.x86_64.rpm 441 kB/s | 62 kB 00:00
(422/686): gnome-bluetooth-libs-3.34.3-1.el8.x86_64.rpm 1.3 MB/s | 326 kB 00:00
(423/686): geoclue2-2.5.5-2.el8.x86_64.rpm 663 kB/s | 132 kB 00:00
(424/686): spice-gtk3-0.38-6.el8.x86_64.rpm 317 kB/s | 76 kB 00:00
(425/686): soundtouch-2.0.0-3.el8.x86_64.rpm 858 kB/s | 76 kB 00:00
(426/686): dconf-0.28.0-4.el8.x86_64.rpm 1.0 MB/s | 108 kB 00:00
(427/686): SDL-1.2.15-39.el8.x86_64.rpm 1.4 MB/s | 218 kB 00:00
(428/686): spice-glib-0.38-6.el8.x86_64.rpm 3.0 MB/s | 385 kB 00:00
(429/686): woff2-1.0.2-5.el8.x86_64.rpm 530 kB/s | 59 kB 00:00
(430/686): libvisual-0.4.0-25.el8.x86_64.rpm 588 kB/s | 145 kB 00:00
(431/686): geocode-glib-3.26.0-3.el8.x86_64.rpm 217 kB/s | 72 kB 00:00
(432/686): spice-server-0.14.3-4.el8.x86_64.rpm 1.6 MB/s | 409 kB 00:00
(433/686): gstreamer1-plugins-base-1.16.1-2.el8.x86_64.rpm 6.6 MB/s | 2.0 MB 00:00
(434/686): uuid-1.6.2-43.el8.x86_64.rpm 233 kB/s | 64 kB 00:00
(435/686): telnet-0.17-76.el8.x86_64.rpm 374 kB/s | 72 kB 00:00
(436/686): geoclue2-libs-2.5.5-2.el8.x86_64.rpm 269 kB/s | 52 kB 00:00
(437/686): jbig2dec-libs-0.16-1.el8.x86_64.rpm 380 kB/s | 72 kB 00:00
(438/686): protobuf-c-1.3.0-6.el8.x86_64.rpm 159 kB/s | 37 kB 00:00
(439/686): gtk2-2.24.32-5.el8.x86_64.rpm 4.8 MB/s | 3.4 MB 00:00
(440/686): python36-3.6.8-38.module+el8.5.0+12207+5c5719bc.x86_64.rpm 188 kB/s | 19 kB 00:00
(441/686): libjpeg-turbo-1.5.3-12.el8.x86_64.rpm 1.3 MB/s | 157 kB 00:00
(442/686): ipmitool-1.8.18-18.el8.x86_64.rpm 1.6 MB/s | 395 kB 00:00
(443/686): lua-5.3.4-12.el8.x86_64.rpm 733 kB/s | 192 kB 00:00
(444/686): xorg-x11-font-utils-7.5-41.el8.x86_64.rpm 825 kB/s | 104 kB 00:00
(445/686): libevdev-1.10.0-1.el8.x86_64.rpm 96 kB/s | 44 kB 00:00
(446/686): libX11-xcb-1.6.8-5.el8.x86_64.rpm 43 kB/s | 14 kB 00:00
(447/686): libgweather-3.28.2-4.el8.x86_64.rpm 6.1 MB/s | 3.1 MB 00:00
(448/686): glusterfs-cli-6.0-56.4.el8.x86_64.rpm 658 kB/s | 194 kB 00:00
(449/686): grilo-0.3.6-3.el8.x86_64.rpm 450 kB/s | 220 kB 00:00
(450/686): vino-3.22.0-11.el8.x86_64.rpm 1.7 MB/s | 461 kB 00:00
(451/686): libepoxy-1.5.8-1.el8.x86_64.rpm 1.1 MB/s | 225 kB 00:00
(452/686): perl-GSSAPI-0.28-25.el8.x86_64.rpm 164 kB/s | 64 kB 00:00
(453/686): pango-1.42.4-8.el8.x86_64.rpm 1.3 MB/s | 297 kB 00:00
(454/686): glusterfs-api-6.0-56.4.el8.x86_64.rpm 305 kB/s | 99 kB 00:00
(455/686): libX11-1.6.8-5.el8.x86_64.rpm 3.4 MB/s | 611 kB 00:00
(456/686): libwacom-data-1.6-3.el8.noarch.rpm 183 kB/s | 104 kB 00:00
(457/686): ibus-gtk2-1.5.19-14.el8_5.x86_64.rpm 333 kB/s | 62 kB 00:00
(458/686): libwacom-1.6-3.el8.x86_64.rpm 61 kB/s | 42 kB 00:00
(459/686): ibus-setup-1.5.19-14.el8_5.noarch.rpm 356 kB/s | 97 kB 00:00
(460/686): ibus-libs-1.5.19-14.el8_5.x86_64.rpm 1.3 MB/s | 265 kB 00:00
(461/686): jasper-libs-2.0.14-5.el8.x86_64.rpm 519 kB/s | 167 kB 00:00
(462/686): ibus-gtk3-1.5.19-14.el8_5.x86_64.rpm 81 kB/s | 63 kB 00:00
(463/686): libX11-common-1.6.8-5.el8.noarch.rpm 658 kB/s | 158 kB 00:00
(464/686): perl-DBI-1.641-4.module+el8.6.0+13388+70c0920f.x86_64.rpm 2.4 MB/s | 741 kB 00:00
(465/686): mdevctl-1.1.0-2.el8.x86_64.rpm 2.5 MB/s | 755 kB 00:00
(466/686): accountsservice-0.6.55-4.el8.x86_64.rpm 737 kB/s | 139 kB 00:00
(467/686): adwaita-cursor-theme-3.28.0-3.el8.noarch.rpm 2.4 MB/s | 647 kB 00:00
(468/686): pixman-0.38.4-2.el8.x86_64.rpm 672 kB/s | 257 kB 00:00
(469/686): cairo-gobject-1.15.12-6.el8.x86_64.rpm 178 kB/s | 33 kB 00:00
(470/686): tcpdump-4.9.3-3.el8.x86_64.rpm 2.4 MB/s | 453 kB 00:00
(471/686): ibus-1.5.19-14.el8_5.x86_64.rpm 4.1 MB/s | 9.1 MB 00:02
(472/686): aspell-0.60.6.1-22.el8.x86_64.rpm 3.2 MB/s | 673 kB 00:00
(473/686): cairo-1.15.12-6.el8.x86_64.rpm 3.3 MB/s | 719 kB 00:00
(474/686): virt-manager-common-3.2.0-4.el8.noarch.rpm 3.7 MB/s | 1.0 MB 00:00
(475/686): redhat-backgrounds-84.5-1.el8.noarch.rpm 10 MB/s | 42 MB 00:04
(476/686): adwaita-icon-theme-3.28.0-3.el8.noarch.rpm 8.7 MB/s | 11 MB 00:01
(477/686): netpbm-progs-10.82.00-7.el8.x86_64.rpm 2.8 MB/s | 2.2 MB 00:00
(478/686): mozilla-filesystem-1.9-19.el8.x86_64.rpm 109 kB/s | 11 kB 00:00
(479/686): libglvnd-glx-1.3.4-1.el8.x86_64.rpm 721 kB/s | 137 kB 00:00
(480/686): libpq-13.5-1.el8.x86_64.rpm 952 kB/s | 198 kB 00:00
(481/686): libglvnd-egl-1.3.4-1.el8.x86_64.rpm 542 kB/s | 49 kB 00:00
(482/686): libnotify-0.7.7-6.el8.x86_64.rpm 467 kB/s | 47 kB 00:00
(483/686): netpbm-10.82.00-7.el8.x86_64.rpm 169 kB/s | 206 kB 00:01
(484/686): accountsservice-libs-0.6.55-4.el8.x86_64.rpm 1.1 MB/s | 96 kB 00:00
(485/686): python3-pip-9.0.3-22.el8.noarch.rpm 200 kB/s | 20 kB 00:00
(486/686): libglvnd-1.3.4-1.el8.x86_64.rpm 1.0 MB/s | 128 kB 00:00
(487/686): webrtc-audio-processing-0.3-10.el8.x86_64.rpm 2.6 MB/s | 297 kB 00:00
(488/686): libosinfo-1.9.0-3.el8.x86_64.rpm 1.1 MB/s | 301 kB 00:00
(489/686): libglvnd-gles-1.3.4-1.el8.x86_64.rpm 158 kB/s | 40 kB 00:00
(490/686): python3-suds-0.7-0.11.94664ddd46a6.el8.noarch.rpm 1.2 MB/s | 242 kB 00:00
(491/686): libglvnd-opengl-1.3.4-1.el8.x86_64.rpm 478 kB/s | 47 kB 00:00
(492/686): libinput-1.16.3-3.el8_6.x86_64.rpm 1.6 MB/s | 217 kB 00:00
(493/686): cheese-libs-3.28.0-4.el8_6.x86_64.rpm 4.7 MB/s | 826 kB 00:00
(494/686): fribidi-1.0.4-9.el8.x86_64.rpm 1.0 MB/s | 89 kB 00:00
(495/686): openjpeg2-2.4.0-5.el8.x86_64.rpm 1.0 MB/s | 165 kB 00:00
(496/686): createrepo_c-0.17.7-6.el8.x86_64.rpm 830 kB/s | 89 kB 00:00
(497/686): yajl-2.1.0-11.el8.x86_64.rpm 422 kB/s | 41 kB 00:00
(498/686): wavpack-5.1.0-16.el8.x86_64.rpm 911 kB/s | 191 kB 00:00
(499/686): virt-manager-3.2.0-4.el8.noarch.rpm 807 kB/s | 621 kB 00:00
(500/686): tftp-server-5.2-26.el8.x86_64.rpm 138 kB/s | 51 kB 00:00
(501/686): sbd-1.5.1-2.el8.x86_64.rpm 86 kB/s | 80 kB 00:00
(502/686): boost-thread-1.66.0-13.el8.x86_64.rpm 629 kB/s | 59 kB 00:00
(503/686): libwsman1-2.6.5-9.el8.x86_64.rpm 214 kB/s | 142 kB 00:00
(504/686): boost-date-time-1.66.0-13.el8.x86_64.rpm 190 kB/s | 30 kB 00:00
(505/686): createrepo_c-libs-0.17.7-6.el8.x86_64.rpm 932 kB/s | 116 kB 00:00
(506/686): evolution-data-server-langpacks-3.28.5-20.el8.noarch.rpm 7.7 MB/s | 1.4 MB 00:00
(507/686): boost-chrono-1.66.0-13.el8.x86_64.rpm 226 kB/s | 23 kB 00:00
(508/686): osinfo-db-20220727-2.el8.noarch.rpm 1.6 MB/s | 267 kB 00:00
(509/686): libnma-1.8.38-1.el8.x86_64.rpm 2.7 MB/s | 291 kB 00:00
(510/686): fstrm-0.6.1-3.el8.x86_64.rpm 257 kB/s | 29 kB 00:00
(511/686): gtk-update-icon-cache-3.22.30-11.el8.x86_64.rpm 427 kB/s | 33 kB 00:00
(512/686): libverto-libev-0.3.2-2.el8.x86_64.rpm 81 kB/s | 16 kB 00:00
(513/686): ipxe-roms-qemu-20181214-11.git133f4c47.el8.noarch.rpm 3.3 MB/s | 1.2 MB 00:00
(514/686): boost-program-options-1.66.0-13.el8.x86_64.rpm 1.6 MB/s | 141 kB 00:00
(515/686): flatpak-1.10.7-1.el8.x86_64.rpm 4.7 MB/s | 1.7 MB 00:00
(516/686): pulseaudio-libs-glib2-14.0-4.el8.x86_64.rpm 257 kB/s | 31 kB 00:00
(517/686): flatpak-selinux-1.10.7-1.el8.noarch.rpm 310 kB/s | 27 kB 00:00
(518/686): pulseaudio-14.0-4.el8.x86_64.rpm 5.3 MB/s | 1.0 MB 00:00
(519/686): xdg-desktop-portal-gtk-1.8.0-1.el8.x86_64.rpm 1.3 MB/s | 223 kB 00:00
(520/686): pulseaudio-libs-14.0-4.el8.x86_64.rpm 3.8 MB/s | 682 kB 00:00
(521/686): flatpak-session-helper-1.10.7-1.el8.x86_64.rpm 397 kB/s | 78 kB 00:00
(522/686): nm-connection-editor-1.26.0-1.el8.x86_64.rpm 4.4 MB/s | 851 kB 00:00
(523/686): evolution-data-server-3.28.5-20.el8.x86_64.rpm 5.4 MB/s | 2.1 MB 00:00
(524/686): boost-system-1.66.0-13.el8.x86_64.rpm 193 kB/s | 18 kB 00:00
(525/686): libgdata-0.17.9-4.el8.x86_64.rpm 2.3 MB/s | 454 kB 00:00
(526/686): openwsman-python3-2.6.5-9.el8.x86_64.rpm 205 kB/s | 122 kB 00:00
(527/686): nmap-ncat-7.70-8.el8.x86_64.rpm 654 kB/s | 237 kB 00:00
(528/686): gstreamer1-plugins-good-1.16.1-3.el8.x86_64.rpm 4.6 MB/s | 2.3 MB 00:00
(529/686): nmap-7.70-8.el8.x86_64.rpm 7.2 MB/s | 5.8 MB 00:00
(530/686): boost-iostreams-1.66.0-13.el8.x86_64.rpm 501 kB/s | 42 kB 00:00
(531/686): boost-regex-1.66.0-13.el8.x86_64.rpm 603 kB/s | 281 kB 00:00
(532/686): boost-atomic-1.66.0-13.el8.x86_64.rpm 75 kB/s | 14 kB 00:00
(533/686): zenity-3.28.1-2.el8.x86_64.rpm 6.3 MB/s | 4.0 MB 00:00
(534/686): xdg-desktop-portal-1.8.1-1.el8.x86_64.rpm 2.0 MB/s | 418 kB 00:00
(535/686): gtk3-3.22.30-11.el8.x86_64.rpm 7.4 MB/s | 4.5 MB 00:00
(536/686): pulseaudio-module-bluetooth-14.0-4.el8.x86_64.rpm 650 kB/s | 89 kB 00:00
(537/686): openssh-askpass-8.0p1-17.el8_7.x86_64.rpm 499 kB/s | 94 kB 00:00
(538/686): postgresql-10.23-1.module+el8.7.0+17280+3a452e1f.x86_64.rpm 5.3 MB/s | 1.5 MB 00:00
(539/686): boost-random-1.66.0-13.el8.x86_64.rpm 191 kB/s | 22 kB 00:00
(540/686): postgresql-contrib-10.23-1.module+el8.7.0+17280+3a452e1f.x86_64.rpm 991 kB/s | 811 kB 00:00
(541/686): libwebp-1.0.0-8.el8_7.x86_64.rpm 2.3 MB/s | 273 kB 00:00
(542/686): postgresql-server-10.23-1.module+el8.7.0+17280+3a452e1f.x86_64.rpm 5.1 MB/s | 5.1 MB 00:00
(543/686): netcf-libs-0.2.8-12.module+el8.8.0+16781+9f4724c2.x86_64.rpm 648 kB/s | 77 kB 00:00
(544/686): qemu-kvm-6.2.0-32.module+el8.8.0+18361+9f407f6e.x86_64.rpm 1.9 MB/s | 182 kB 00:00
(545/686): libiscsi-1.18.0-8.module+el8.8.0+16781+9f4724c2.x86_64.rpm 994 kB/s | 89 kB 00:00
(546/686): postgresql-plperl-10.23-1.module+el8.7.0+17280+3a452e1f.x86_64.rpm 140 kB/s | 103 kB 00:00
(547/686): gnutls-dane-3.6.16-6.el8_7.x86_64.rpm 56 kB/s | 52 kB 00:00
(548/686): mesa-libGL-22.3.0-2.el8.x86_64.rpm 1.0 MB/s | 188 kB 00:00
(549/686): fence-agents-rsb-4.2.1-112.el8.noarch.rpm 37 kB/s | 27 kB 00:00
(550/686): qemu-kvm-block-ssh-6.2.0-32.module+el8.8.0+18361+9f407f6e.x86_64.rpm 1.0 MB/s | 195 kB 00:00
(551/686): gnutls-utils-3.6.16-6.el8_7.x86_64.rpm 1.2 MB/s | 349 kB 00:00
(552/686): fence-agents-common-4.2.1-112.el8.noarch.rpm 52 kB/s | 72 kB 00:01
(553/686): swtpm-0.7.0-4.20211109gitb79fd91.module+el8.8.0+16781+9f4724c2.x86_64.rpm 180 kB/s | 43 kB 00:00
(554/686): swtpm-tools-0.7.0-4.20211109gitb79fd91.module+el8.8.0+16781+9f4724c2.x86_64.rpm 632 kB/s | 119 kB 00:00
(555/686): qemu-kvm-core-6.2.0-32.module+el8.8.0+18361+9f407f6e.x86_64.rpm 8.3 MB/s | 3.4 MB 00:00
(556/686): qemu-kvm-block-iscsi-6.2.0-32.module+el8.8.0+18361+9f407f6e.x86_64.rpm 745 kB/s | 200 kB 00:00
(557/686): sgabios-bin-0.20170427git-3.module+el8.8.0+16781+9f4724c2.noarch.rpm 51 kB/s | 13 kB 00:00
(558/686): swtpm-libs-0.7.0-4.20211109gitb79fd91.module+el8.8.0+16781+9f4724c2.x86_64.rpm 201 kB/s | 49 kB 00:00
(559/686): seavgabios-bin-1.16.0-3.module+el8.8.0+16781+9f4724c2.noarch.rpm 164 kB/s | 44 kB 00:00
(560/686): qemu-kvm-hw-usbredir-6.2.0-32.module+el8.8.0+18361+9f407f6e.x86_64.rpm 662 kB/s | 204 kB 00:00
(561/686): qemu-img-6.2.0-32.module+el8.8.0+18361+9f407f6e.x86_64.rpm 3.8 MB/s | 2.2 MB 00:00
(562/686): perl-Sys-Virt-8.0.0-1.module+el8.8.0+16781+9f4724c2.x86_64.rpm 1.0 MB/s | 325 kB 00:00
(563/686): qemu-kvm-block-curl-6.2.0-32.module+el8.8.0+18361+9f407f6e.x86_64.rpm 879 kB/s | 192 kB 00:00
(564/686): qemu-kvm-ui-spice-6.2.0-32.module+el8.8.0+18361+9f407f6e.x86_64.rpm 1.3 MB/s | 243 kB 00:00
(565/686): upower-0.99.7-4.el8_7.x86_64.rpm 696 kB/s | 171 kB 00:00
(566/686): qemu-kvm-block-gluster-6.2.0-32.module+el8.8.0+18361+9f407f6e.x86_64.rpm 898 kB/s | 194 kB 00:00
(567/686): qemu-kvm-block-rbd-6.2.0-32.module+el8.8.0+18361+9f407f6e.x86_64.rpm 1.0 MB/s | 195 kB 00:00
(568/686): qemu-kvm-ui-opengl-6.2.0-32.module+el8.8.0+18361+9f407f6e.x86_64.rpm 203 kB/s | 196 kB 00:00
(569/686): qemu-kvm-common-6.2.0-32.module+el8.8.0+18361+9f407f6e.x86_64.rpm 3.9 MB/s | 1.1 MB 00:00
(570/686): seabios-bin-1.16.0-3.module+el8.8.0+16781+9f4724c2.noarch.rpm 1.4 MB/s | 138 kB 00:00
(571/686): python3-libvirt-8.0.0-2.module+el8.8.0+16781+9f4724c2.x86_64.rpm 1.7 MB/s | 332 kB 00:00
(572/686): qemu-kvm-docs-6.2.0-32.module+el8.8.0+18361+9f407f6e.x86_64.rpm 3.6 MB/s | 2.6 MB 00:00
(573/686): wget-1.19.5-11.el8.x86_64.rpm 3.8 MB/s | 734 kB 00:00
(574/686): libdrm-2.4.114-1.el8.x86_64.rpm 357 kB/s | 165 kB 00:00
(575/686): mesa-libEGL-22.3.0-2.el8.x86_64.rpm 1.4 MB/s | 147 kB 00:00
(576/686): fence-agents-bladecenter-4.2.1-112.el8.noarch.rpm 148 kB/s | 28 kB 00:00
(577/686): libwayland-egl-1.21.0-1.el8.x86_64.rpm 73 kB/s | 20 kB 00:00
(578/686): mesa-libglapi-22.3.0-2.el8.x86_64.rpm 354 kB/s | 67 kB 00:00
(579/686): llvm-libs-15.0.7-1.module+el8.8.0+17939+b58878af.x86_64.rpm 10 MB/s | 27 MB 00:02
(580/686): fence-agents-scsi-4.2.1-112.el8.noarch.rpm 34 kB/s | 32 kB 00:00
(581/686): libwayland-client-1.21.0-1.el8.x86_64.rpm 484 kB/s | 41 kB 00:00
(582/686): fence-agents-ilo-ssh-4.2.1-112.el8.noarch.rpm 34 kB/s | 34 kB 00:00
(583/686): fence-agents-cisco-ucs-4.2.1-112.el8.noarch.rpm 23 kB/s | 28 kB 00:01
(584/686): fence-agents-redfish-4.2.1-112.el8.x86_64.rpm 14 kB/s | 28 kB 00:02
(585/686): fence-agents-brocade-4.2.1-112.el8.noarch.rpm 22 kB/s | 28 kB 00:01
(586/686): fence-agents-sbd-4.2.1-112.el8.noarch.rpm 20 kB/s | 29 kB 00:01
(587/686): fence-agents-ipmilan-4.2.1-112.el8.noarch.rpm 29 kB/s | 42 kB 00:01
(588/686): net-snmp-utils-5.8-27.el8.x86_64.rpm 1.0 MB/s | 240 kB 00:00
(589/686): fence-agents-heuristics-ping-4.2.1-112.el8.noarch.rpm 44 kB/s | 28 kB 00:00
(590/686): xorg-x11-server-Xwayland-21.1.3-10.el8.x86_64.rpm 3.9 MB/s | 966 kB 00:00
(591/686): dnsmasq-2.79-26.el8.x86_64.rpm 1.2 MB/s | 321 kB 00:00
(592/686): wpebackend-fdo-1.10.0-3.el8.x86_64.rpm 234 kB/s | 44 kB 00:00
(593/686): libwayland-server-1.21.0-1.el8.x86_64.rpm 126 kB/s | 49 kB 00:00
(594/686): libwayland-cursor-1.21.0-1.el8.x86_64.rpm 138 kB/s | 26 kB 00:00
(595/686): gnome-online-accounts-3.28.2-4.el8.x86_64.rpm 966 kB/s | 547 kB 00:00
(596/686): ghostscript-9.27-6.el8.x86_64.rpm 211 kB/s | 83 kB 00:00
(597/686): gnome-settings-daemon-3.32.0-19.el8.x86_64.rpm 4.6 MB/s | 1.1 MB 00:00
(598/686): mesa-filesystem-22.3.0-2.el8.x86_64.rpm 110 kB/s | 35 kB 00:00
(599/686): gnome-control-center-filesystem-3.28.2-37.el8.noarch.rpm 27 kB/s | 13 kB 00:00
(600/686): mesa-libgbm-22.3.0-2.el8.x86_64.rpm 227 kB/s | 60 kB 00:00
(601/686): gcc-8.5.0-18.el8.x86_64.rpm 8.7 MB/s | 23 MB 00:02
(602/686): fence-agents-drac5-4.2.1-112.el8.noarch.rpm 71 kB/s | 28 kB 00:00
(603/686): gdm-40.0-27.el8.x86_64.rpm 3.1 MB/s | 881 kB 00:00
(604/686): cpp-8.5.0-18.el8.x86_64.rpm 6.5 MB/s | 10 MB 00:01
(605/686): fence-agents-virsh-4.2.1-112.el8.noarch.rpm 196 kB/s | 28 kB 00:00
(606/686): fence-agents-ilo-mp-4.2.1-112.el8.noarch.rpm 380 kB/s | 27 kB 00:00
(607/686): fence-agents-mpath-4.2.1-112.el8.noarch.rpm 161 kB/s | 30 kB 00:00
(608/686): dbus-x11-1.12.8-24.el8.x86_64.rpm 288 kB/s | 61 kB 00:00
(609/686): edk2-ovmf-20220126gitbb1bba3d77-4.el8.noarch.rpm 8.0 MB/s | 3.6 MB 00:00
(610/686): xorg-x11-server-common-1.20.11-15.el8.x86_64.rpm 178 kB/s | 44 kB 00:00
(611/686): annobin-10.94-1.el8.x86_64.rpm 3.2 MB/s | 965 kB 00:00
(612/686): gcc-plugin-annobin-8.5.0-18.el8.x86_64.rpm 399 kB/s | 35 kB 00:00
(613/686): desktop-file-utils-0.26-1.el8.x86_64.rpm 294 kB/s | 80 kB 00:00
(614/686): ostree-libs-2022.2-6.el8.x86_64.rpm 1.8 MB/s | 446 kB 00:00
(615/686): fence-agents-cisco-mds-4.2.1-112.el8.noarch.rpm 147 kB/s | 28 kB 00:00
(616/686): fence-agents-vmware-rest-4.2.1-112.el8.noarch.rpm 65 kB/s | 28 kB 00:00
(617/686): fence-agents-ilo-moonshot-4.2.1-112.el8.noarch.rpm 295 kB/s | 27 kB 00:00
(618/686): libwpe-1.10.0-4.el8.x86_64.rpm 109 kB/s | 26 kB 00:00
(619/686): fence-agents-apc-4.2.1-112.el8.noarch.rpm 129 kB/s | 29 kB 00:00
(620/686): fence-agents-eaton-snmp-4.2.1-112.el8.noarch.rpm 287 kB/s | 29 kB 00:00
(621/686): fence-agents-ilo2-4.2.1-112.el8.noarch.rpm 140 kB/s | 30 kB 00:00
(622/686): fence-agents-rhevm-4.2.1-112.el8.noarch.rpm 272 kB/s | 29 kB 00:00
(623/686): gnome-control-center-3.28.2-37.el8.x86_64.rpm 6.1 MB/s | 4.8 MB 00:00
(624/686): fence-agents-ipdu-4.2.1-112.el8.noarch.rpm 101 kB/s | 28 kB 00:00
(625/686): xorg-x11-server-Xorg-1.20.11-15.el8.x86_64.rpm 5.2 MB/s | 1.5 MB 00:00
(626/686): fence-agents-all-4.2.1-112.el8.x86_64.rpm 28 kB/s | 25 kB 00:00
(627/686): mesa-dri-drivers-22.3.0-2.el8.x86_64.rpm 8.7 MB/s | 7.3 MB 00:00
(628/686): fence-virt-1.0.0-6.el8.x86_64.rpm 126 kB/s | 52 kB 00:00
(629/686): usbredir-0.12.0-4.el8.x86_64.rpm 223 kB/s | 52 kB 00:00
(630/686): fence-agents-emerson-4.2.1-112.el8.noarch.rpm 141 kB/s | 27 kB 00:00
(631/686): gnome-shell-3.32.2-50.el8.x86_64.rpm 6.2 MB/s | 1.5 MB 00:00
(632/686): fence-agents-amt-ws-4.2.1-112.el8.noarch.rpm 37 kB/s | 29 kB 00:00
(633/686): fence-agents-kdump-4.2.1-112.el8.x86_64.rpm 213 kB/s | 40 kB 00:00
(634/686): fence-agents-apc-snmp-4.2.1-112.el8.noarch.rpm 23 kB/s | 29 kB 00:01
(635/686): libsndfile-1.0.28-13.el8.x86_64.rpm 807 kB/s | 193 kB 00:00
(636/686): libgs-9.27-6.el8.x86_64.rpm 8.8 MB/s | 3.1 MB 00:00
(637/686): fence-agents-rsa-4.2.1-112.el8.noarch.rpm 20 kB/s | 27 kB 00:01
(638/686): fence-agents-vmware-soap-4.2.1-112.el8.noarch.rpm 157 kB/s | 29 kB 00:00
(639/686): fence-agents-hpblade-4.2.1-112.el8.noarch.rpm 25 kB/s | 28 kB 00:01
(640/686): alsa-lib-1.2.8-2.el8.x86_64.rpm 1.7 MB/s | 497 kB 00:00
(641/686): fence-agents-eps-4.2.1-112.el8.noarch.rpm 326 kB/s | 28 kB 00:00
(642/686): fence-agents-intelmodular-4.2.1-112.el8.noarch.rpm 341 kB/s | 28 kB 00:00
(643/686): fence-agents-compute-4.2.1-112.el8.noarch.rpm 186 kB/s | 35 kB 00:00
(644/686): fence-agents-wti-4.2.1-112.el8.noarch.rpm 26 kB/s | 29 kB 00:01
(645/686): fence-agents-ifmib-4.2.1-112.el8.noarch.rpm 28 kB/s | 28 kB 00:00
(646/686): gnome-session-3.28.1-20.el8_8.x86_64.rpm 3.5 MB/s | 381 kB 00:00
(647/686): gnome-session-wayland-session-3.28.1-20.el8_8.x86_64.rpm 114 kB/s | 9.5 kB 00:00
(648/686): fence-agents-ibmblade-4.2.1-112.el8.noarch.rpm 18 kB/s | 27 kB 00:01
(649/686): pacemaker-schemas-2.1.5-8.1.el8_8.noarch.rpm 534 kB/s | 101 kB 00:00
(650/686): gnome-session-xsession-3.28.1-20.el8_8.x86_64.rpm 69 kB/s | 14 kB 00:00
(651/686): corosynclib-3.1.7-1.el8.x86_64.rpm 58 kB/s | 69 kB 00:01
(652/686): libvirt-daemon-driver-interface-8.0.0-19.2.module+el8.8.0+18944+7f5acf75.x86_64.rpm 2.2 MB/s | 214 kB 00:00
(653/686): libvirt-daemon-kvm-8.0.0-19.2.module+el8.8.0+18944+7f5acf75.x86_64.rpm 683 kB/s | 69 kB 00:00
(654/686): libvirt-daemon-driver-nwfilter-8.0.0-19.2.module+el8.8.0+18944+7f5acf75.x86_64.rpm 2.1 MB/s | 239 kB 00:00
(655/686): libvirt-libs-8.0.0-19.2.module+el8.8.0+18944+7f5acf75.x86_64.rpm 8.6 MB/s | 4.7 MB 00:00
(656/686): libvirt-daemon-driver-storage-8.0.0-19.2.module+el8.8.0+18944+7f5acf75.x86_64.rpm 157 kB/s | 70 kB 00:00
(657/686): mutter-3.32.2-69.el8_8.x86_64.rpm 6.7 MB/s | 2.5 MB 00:00
(658/686): libvirt-daemon-driver-nodedev-8.0.0-19.2.module+el8.8.0+18944+7f5acf75.x86_64.rpm 2.1 MB/s | 224 kB 00:00
(659/686): libvirt-daemon-driver-storage-scsi-8.0.0-19.2.module+el8.8.0+18944+7f5acf75.x86_64.rpm 868 kB/s | 77 kB 00:00
(660/686): pacemaker-libs-2.1.5-8.1.el8_8.x86_64.rpm 4.3 MB/s | 761 kB 00:00
(661/686): libvirt-daemon-driver-storage-core-8.0.0-19.2.module+el8.8.0+18944+7f5acf75.x86_64.rpm 2.2 MB/s | 258 kB 00:00
(662/686): libvirt-daemon-driver-secret-8.0.0-19.2.module+el8.8.0+18944+7f5acf75.x86_64.rpm 1.5 MB/s | 202 kB 00:00
(663/686): libvirt-daemon-driver-storage-disk-8.0.0-19.2.module+el8.8.0+18944+7f5acf75.x86_64.rpm 854 kB/s | 80 kB 00:00
(664/686): libtiff-4.0.9-28.el8_8.x86_64.rpm 1.7 MB/s | 189 kB 00:00
(665/686): libvirt-daemon-config-network-8.0.0-19.2.module+el8.8.0+18944+7f5acf75.x86_64.rpm 784 kB/s | 72 kB 00:00
(666/686): libvirt-daemon-8.0.0-19.2.module+el8.8.0+18944+7f5acf75.x86_64.rpm 1.7 MB/s | 423 kB 00:00
(667/686): libvirt-daemon-driver-storage-mpath-8.0.0-19.2.module+el8.8.0+18944+7f5acf75.x86_64.rp 719 kB/s | 75 kB 00:00
(668/686): libvirt-daemon-driver-qemu-8.0.0-19.2.module+el8.8.0+18944+7f5acf75.x86_64.rpm 2.8 MB/s | 928 kB 00:00
(669/686): libvirt-daemon-driver-storage-iscsi-direct-8.0.0-19.2.module+el8.8.0+18944+7f5acf75.x8 693 kB/s | 79 kB 00:00
(670/686): libvirt-daemon-driver-storage-iscsi-8.0.0-19.2.module+el8.8.0+18944+7f5acf75.x86_64.rp 603 kB/s | 77 kB 00:00
(671/686): pacemaker-cluster-libs-2.1.5-8.1.el8_8.x86_64.rpm 1.2 MB/s | 146 kB 00:00
(672/686): libvirt-daemon-driver-network-8.0.0-19.2.module+el8.8.0+18944+7f5acf75.x86_64.rpm 1.9 MB/s | 239 kB 00:00
(673/686): libvirt-daemon-driver-storage-gluster-8.0.0-19.2.module+el8.8.0+18944+7f5acf75.x86_64. 733 kB/s | 82 kB 00:00
(674/686): libvirt-client-8.0.0-19.2.module+el8.8.0+18944+7f5acf75.x86_64.rpm 2.1 MB/s | 419 kB 00:00
(675/686): libvirt-daemon-driver-storage-rbd-8.0.0-19.2.module+el8.8.0+18944+7f5acf75.x86_64.rpm 280 kB/s | 85 kB 00:00
(676/686): libtpms-0.9.1-2.20211126git1ff6fe1f43.module+el8.8.0+18453+1482ba89.x86_64.rpm 639 kB/s | 185 kB 00:00
(677/686): libvirt-daemon-driver-storage-logical-8.0.0-19.2.module+el8.8.0+18944+7f5acf75.x86_64. 702 kB/s | 81 kB 00:00
(678/686): gnome-desktop3-3.32.2-1.el8_8.2.x86_64.rpm 2.6 MB/s | 577 kB 00:00
(679/686): bind-libs-9.11.36-8.el8_8.1.x86_64.rpm 818 kB/s | 176 kB 00:00
(680/686): python3-bind-9.11.36-8.el8_8.1.noarch.rpm 373 kB/s | 151 kB 00:00
(681/686): bind-libs-lite-9.11.36-8.el8_8.1.x86_64.rpm 1.9 MB/s | 1.2 MB 00:00
(682/686): bind-license-9.11.36-8.el8_8.1.noarch.rpm 807 kB/s | 104 kB 00:00
(683/686): bind-utils-9.11.36-8.el8_8.1.x86_64.rpm 2.9 MB/s | 453 kB 00:00
(684/686): webkit2gtk3-jsc-2.38.5-1.el8_8.5.x86_64.rpm 3.7 MB/s | 3.7 MB 00:00
(685/686): webkit2gtk3-2.38.5-1.el8_8.5.x86_64.rpm 7.7 MB/s | 21 MB 00:02
(686/686): firefox-102.13.0-2.el8_8.x86_64.rpm 5.5 MB/s | 109 MB 00:19
----------------------------------------------------------------------------------------------------------------------------------
Total 6.0 MB/s | 601 MB 01:40
Anvil Community Repository (rhel-8) 1.6 MB/s | 1.6 kB 00:00
Importing GPG key 0xD548C925:
Userid : "Alteeve's Niche! Inc. repository <support@alteeve.ca>"
Fingerprint: 3082 E979 518A 78DD 9569 CD2E 9D42 AA76 D548 C925
From : /etc/pki/rpm-gpg/RPM-GPG-KEY-Alteeve-Official
Is this ok [y/N]: y
Key imported successfully
Running transaction check
Transaction check succeeded.
Running transaction test
Transaction test succeeded.
Running transaction
Running scriptlet: npm-1:6.14.11-1.10.24.0.1.module+el8.3.0+10166+b07ac28e.x86_64 1/1
Preparing : 1/1
Installing : gdk-pixbuf2-2.36.12-5.el8.x86_64 1/686
Running scriptlet: gdk-pixbuf2-2.36.12-5.el8.x86_64 1/686
Installing : atk-2.28.1-1.el8.x86_64 2/686
Installing : libwayland-client-1.21.0-1.el8.x86_64 3/686
<...snip...>
<...snip...>
Verifying : bind-utils-32:9.11.36-8.el8_8.1.x86_64 684/686
Verifying : webkit2gtk3-jsc-2.38.5-1.el8_8.5.x86_64 685/686
Verifying : webkit2gtk3-2.38.5-1.el8_8.5.x86_64 686/686
Installed products updated.
Installed:
GConf2-3.2.6-22.el8.x86_64
ModemManager-glib-1.20.2-1.el8.x86_64
NetworkManager-initscripts-updown-1:1.40.16-3.el8_8.noarch
<...snip...>
yum-utils-4.0.21-19.el8_8.noarch
zenity-3.28.1-2.el8.x86_64
zlib-devel-1.2.11-21.el8_7.x86_64
Complete!
Done!
Anvil! Subnode; Installing anvil-node
dnf install anvil-dr
Updating Subscription Management repositories.
Last metadata expiration check: 0:00:47 ago on Fri 28 Jul 2023 06:10:29 PM EDT.
Dependencies resolved.
-=================================================================================================================================
Package Arch Version Repository Size
-=================================================================================================================================
Installing:
anvil-node noarch 2.90-1.2704.25b460.el8 anvil-community-rhel-8 25 k
Installing dependencies:
NetworkManager-initscripts-updown
noarch 1:1.40.16-3.el8_8 rhel-8-for-x86_64-baseos-rpms 143 k
akmod-drbd x86_64 9.2.4-1.el8 anvil-community-rhel-8 1.3 M
akmods noarch 0.5.7-8.el8 anvil-community-rhel-8 34 k
alsa-lib x86_64 1.2.8-2.el8 rhel-8-for-x86_64-appstream-rpms 497 k
annobin x86_64 10.94-1.el8 rhel-8-for-x86_64-appstream-rpms 965 k
anvil-core noarch 2.90-1.2704.25b460.el8 anvil-community-rhel-8 1.0 M
<...snip...>
rubygem-io-console x86_64 0.4.6-110.module+el8.6.0+15956+aa803fc1 rhel-8-for-x86_64-appstream-rpms 68 k
rubygem-rdoc noarch 6.0.1.1-110.module+el8.6.0+15956+aa803fc1 rhel-8-for-x86_64-appstream-rpms 457 k
telnet x86_64 1:0.17-76.el8 rhel-8-for-x86_64-appstream-rpms 72 k
Enabling module streams:
idm client
llvm-toolset rhel8
perl-App-cpanminus 1.7044
perl-DBD-Pg 3.7
perl-DBI 1.641
perl-YAML 1.24
postgresql 10
python36 3.6
ruby 2.5
Transaction Summary
-================================================================================================================================
Install 489 Packages
Total download size: 330 M
Installed size: 1.3 G
Is this ok [y/N]:
Disaster Recovery Host; Installing anvil-dr
dnf install anvil-dr
Updating Subscription Management repositories.
Last metadata expiration check: 0:00:46 ago on Fri 28 Jul 2023 06:10:37 PM EDT.
Dependencies resolved.
-=================================================================================================================================
Package Arch Version Repository Size
-=================================================================================================================================
Installing:
anvil-dr noarch 2.90-1.2704.25b460.el8 anvil-community-rhel-8 8.5 k
Installing dependencies:
NetworkManager-initscripts-updown
noarch 1:1.40.16-3.el8_8 rhel-8-for-x86_64-baseos-rpms 143 k
SDL x86_64 1.2.15-39.el8 rhel-8-for-x86_64-appstream-rpms 218 k
akmod-drbd x86_64 9.2.4-1.el8 anvil-community-rhel-8 1.3 M
akmods noarch 0.5.7-8.el8 anvil-community-rhel-8 34 k
<...snip...>
geolite2-country noarch 20180605-1.el8 rhel-8-for-x86_64-appstream-rpms 1.0 M
openssl-devel x86_64 1:1.1.1k-9.el8_7 rhel-8-for-x86_64-baseos-rpms 2.3 M
telnet x86_64 1:0.17-76.el8 rhel-8-for-x86_64-appstream-rpms 72 k
Enabling module streams:
idm client
llvm-toolset rhel8
perl-App-cpanminus 1.7044
perl-DBD-Pg 3.7
perl-DBI 1.641
perl-YAML 1.24
postgresql 10
python36 3.6
Transaction Summary
-=================================================================================================================================
Install 459 Packages
Total download size: 315 M
Installed size: 1.3 G
Is this ok [y/N]:
File:An-striker01-rhel8-m3-os-install-20.png
No disc in the drive.
Enabling the Alteeve Repo
On all machines, post OS install, add the Anvil! repo;
dnf -y install https://www.alteeve.com/an-repo/m3/anvil-release-latest.noarch.rpm
Once installed, you need to enable the repository.
| Repository Options | |
|---|---|
| Community | This is free, and it gets the latest updates generated by our CI/CD testing infrastructure. |
| Commercial | This is paid and includes a support contract. Updates are curated for maximum reliability. |
If you purchase a commercial support agreement, you will be provided a key to access the commercial repository.
To enable the Anvil! repository, run either:
| Repository Options | |
|---|---|
| Community | alteeve-repo-setup
|
| Commercial | alteeve-repo-setup -k <key>
|
Now update the OS;
dnf update
If the kernel was updated, it is recommended (but not required) to reboot now.
In all cases, the Anvil! will rename network interfaces. For this to work, the biosdevname package needs to be removed.
dnf remove biosdevname
Now, we can install the anvil RPM. This next step is what defines a given machine as a Striker, Node or DR Host. As such, be careful to install the right one for the machine you're configuring.
| Install the Anvil! RPM | |
|---|---|
| Striker Dashboard | dnf install anvil-striker
|
| Node | dnf install anvil-node
|
| DR Host | dnf install anvil-dr
|
| Any questions, feedback, advice, complaints or meanderings are welcome. | ||||
| Us: Alteeve's Niche! | Support: Mailing List | IRC: #clusterlabs on Libera Chat | ||
| © Alteeve's Niche! Inc. 1997-2023 | Anvil! "Intelligent Availability™" Platform | |||
| legal stuff: All info is provided "As-Is". Do not use anything here unless you are willing and able to take responsibility for your own actions. | ||||